ATCP 65.86(3)(b)
(b)
Specific calibration requirements. If an automated testing device is used to test for milkfat, protein, total solids, or solids-not-fat in milk, and if the test results may affect the price paid to a milk producer, the testing device shall be calibrated according to this paragraph. The testing device shall be calibrated, for each relevant milk component, by a tester who is licensed under s.
97.17 or
98.145, Stats., to operate that device.
ATCP 65.86(3)(b)1.
1. `Calibration frequency'. A milk component testing device under par.
(b) shall be calibrated at all of the following times:
ATCP 65.86(3)(b)1.c.
c. Immediately after every significant repair or alteration to the testing device.
ATCP 65.86(3)(b)1.d.
d. Whenever the mean difference on a daily performance check under par.
(c) exceeds plus or minus 0.044% for milkfat or protein or plus or minus 0.084% for total solids or solids-not-fat.
ATCP 65.86(3)(b)2.
2. `Calibration procedure'. To calibrate a milk component testing device under par.
(b), a tester shall use the device to test a set of calibration samples under subd.
3. The milk component testing device shall be adjusted, as necessary, to satisfy all of the following requirements:
ATCP 65.86(3)(b)2.a.
a. The performance error on each calibration sample shall be as near as practicable to zero. The performance error is the difference between the known percentage content of each milk component in the calibration sample, as determined by the sample provider, and the percentage content measured by the testing device.
ATCP 65.86(3)(b)2.b.
b. The mean difference for the entire set of calibration samples shall be as near as practicable to zero and shall not exceed plus or minus 0.044% for milkfat or protein or plus or minus 0.084% for total solids or solids-not-fat. The mean difference is the sum of the performance errors for the individual calibration samples divided by the number of samples in the set.
ATCP 65.86(3)(b)2.c.
c. The standard deviation of test results, calculated for the set of calibration samples according to the formula set forth in the “Official Methods of Analysis of AOAC International," 18th edition (2005), section 969.16, shall not exceed 0.044% for milkfat or protein, or 0.084% for total solids or solids-not-fat.
ATCP 65.86 Note
Note: The “Official Methods of Analysis of AOAC International," 18th edition (2005), is on file with the division and the legislative reference bureau, and may be obtained from AOAC International, 2275 Research Blvd., Rockville, MD 20850, website
https://www.aoac.org .
ATCP 65.86(3)(b)3.
3. `Calibration samples'. A set of calibration samples shall be obtained from a sample provider approved by the division. A set of calibration samples shall consist of at least 12 individual samples, each of which complies with all of the following requirements:
ATCP 65.86(3)(b)3.b.
b. Each sample shall be a fresh milk sample preserved with bronopol (2-bromo-2-nitro-1, 3-propanediol) or another approved preservative. Preservative methods, formulations, and concentrations shall be approved by the division.
ATCP 65.86(3)(b)3.c.
c. Each sample shall have a known percentage content of each relevant milk component determined by the sample provider under pars.
(e) to
(h).
ATCP 65.86(3)(c)1.1. If an automated testing device is used to test for milkfat, protein, total solids, or solids-not-fat in milk, and if the test results may affect the price paid to a milk producer, the device shall be subjected to a daily performance check before each day's testing. The daily performance check shall be conducted, for each relevant milk component, by a tester who is licensed under s.
97.17 or
98.145, Stats., to operate the testing device.
ATCP 65.86(3)(c)2.
2. To conduct a daily performance check under subd.
1., a tester shall test a set of daily performance check samples under subd.
4. Based on the daily performance check, the tester shall do all of the following:
ATCP 65.86(3)(c)2.a.
a. Determine the performance error of the testing device with respect to each daily performance check sample. The performance error is the difference between the known percentage content of each milk component in that sample, as determined by the sample provider, and the percentage content measured by the testing device.
ATCP 65.86(3)(c)2.b.
b. Based on the performance errors for the individual samples under subdivision paragraph a, calculate the mean difference for the set of daily performance check samples. The mean difference is the sum of the performance errors for the individual samples, divided by the number of samples in the set.
ATCP 65.86(3)(c)3.
3. If, on a daily performance check under subd.
1., the mean difference calculated under sub.
(2) (b) exceeds plus or minus 0.044% for milkfat or protein or plus or minus 0.084% for total solids or solids-not-fat the testing device shall not be used until it is recalibrated under par.
(b).
ATCP 65.86(3)(c)4.
4. A set of daily performance check samples shall be obtained from a sample provider approved by the division. A set shall consist of at least 5 individual samples, each of which complies with all of the following requirements:
ATCP 65.86(3)(c)4.b.
b. Each sample shall be a fresh milk sample preserved with bronopol (2-bromo-2-nitro-1, 3-propanediol) or another approved preservative. Preservative methods, formulations, and concentrations shall be approved by the department.
ATCP 65.86(3)(c)4.c.
c. Each sample shall have a known percentage content of each relevant milk component, determined by the sample provider under pars.
(e) to
(h).
ATCP 65.86(3)(d)1.1. If an automated testing device is used to test for milkfat, protein, total solids, or solids-not-fat in milk, and if the test results may affect the price paid to a milk producer, that device shall be subjected to a daily reference check under subd. 2 and hourly reference checks under subd.
3. ATCP 65.86(3)(d)2.
2. A daily reference check required under subd. 1 shall be done in accordance with all of the following requirements:
ATCP 65.86(3)(d)2.a.
a. A daily reference check shall be conducted before each day's testing, at the same time that the dairy plant operator conducts the daily performance check under par.
(c). The daily reference check shall be conducted, for each relevant milk component by a tester who is licensed under s.
97.17 or
98.145, Stats., to operate the testing device.
ATCP 65.86(3)(d)2.b.
b. To perform a daily reference check, a tester shall perform 10 tests on a reference sample. The reference sample may be a homogenized milk sample prepared by the dairy plant operator, or it may be a daily performance check sample obtained from a sample provider approved by the department under par.
(c) 4. The 10 test results shall be averaged and the average result shall be used as a comparison value for the hourly reference checks under subd.
3. ATCP 65.86(3)(d)3.
3. An hourly reference check required under subd. 1 shall be done in accordance with all of the following requirements:
ATCP 65.86(3)(d)3.a.
a. An hourly reference check shall be conducted for each milk component before each hour's testing for that component. To conduct an hourly reference check, a tester shall test the same reference sample used for the daily reference check under subd.
2. ATCP 65.86(3)(d)3.b.
b. For each relevant milk component the hourly reference check result shall be compared to the average result obtained on the daily reference check under subd.
2. If an hourly reference check result differs from the average result on the daily reference check by more than 0.034% for milkfat or protein or 0.064% for total solids or solids-not-fat, the testing device shall not be used until the condition causing the difference is found and corrected. Test results obtained before the device is corrected, and after the last previous conforming reference check, shall not be used in determining the amount paid to milk producers.
ATCP 65.86(3)(e)
(e)
Calibration and daily performance check samples; milkfat contents. ATCP 65.86(3)(e)1.1. The provider of a calibration sample under par.
(b) or a daily performance check sample under par.
(c) shall determine the known percentage content of milkfat in that sample by averaging the results of 3 milkfat tests using a method specified under subd.
4. The percentage milkfat results from those 3 milkfat tests shall not vary by more than 0.034 percentage points.
ATCP 65.86(3)(e)2.
2. The known milkfat content of a calibration sample, expressed as a percentage of the sample weight, shall be at least 2.5%. Within a set of calibration samples, the difference in known milkfat content between the lowest milkfat sample and the highest milkfat sample, expressed as a percentage of average sample weight, shall be at least 2.5%.
ATCP 65.86(3)(e)3.
3. The known milkfat content of a daily performance check sample, expressed as a percentage of the sample weight, shall be at least 2.8%. Within a set of daily performance check samples, the difference in known milkfat content between the lowest milkfat sample and the highest milkfat sample, expressed as a percentage of average sample weight, shall be at least 1.5%.
ATCP 65.86(3)(e)4.
4. To determine the milkfat content of a calibration sample or daily performance check sample, the sample provider shall use either a manual or robotic version of the Modified Mojonnier method as described in the "Official Methods of Analysis of AOAC International," 18th edition (2005), section 989.05.
ATCP 65.86 Note
Note: The “Official Methods of Analysis of AOAC International," 18th edition (2005), is on file with the division and the legislative reference bureau, and may be obtained from AOAC International, 2275 Research Blvd., Rockville, MD 20850, website
https://www.aoac.org .
ATCP 65.86(3)(f)
(f)
Calibration and daily performance check samples; protein contents. ATCP 65.86(3)(f)1.1. The provider of a calibration sample under par.
(b) or a daily performance check sample under par.
(c) shall determine the known percentage content of protein in that sample by averaging the results of 3 protein tests using the method specified under subd.
3. The percentage protein results from those 3 tests shall not vary by more than 0.034 percentage points.
ATCP 65.86(3)(f)2.
2. The known protein content of a calibration or daily performance check sample, expressed as a percentage of sample weight, shall be at least 2.7%. Within a set of calibration samples, the difference in known protein content between the lowest protein sample and the highest protein sample, expressed as a percentage of average sample weight, shall be at least 0.7%. Within a set of daily performance check samples, the difference in known protein content between the lowest protein sample and the highest protein sample, expressed as a percentage of average sample weight, shall be at least 0.5%.
ATCP 65.86(3)(f)3.
3. To determine the protein content of a calibration sample or daily performance check sample, the sample provider shall use the traditional or block digester/steam distillation Kjeldahl method as described in the “Official Methods of Analysis of AOAC International," 18th edition (2005), section 991.20.
ATCP 65.86 Note
Note: The “Official Methods of Analysis of AOAC International," 18th edition (2005), is on file with the division and the legislative reference bureau, and may be obtained from AOAC International, 2275 Research Blvd., Rockville, MD 20850, website
https://www.aoac.org .
ATCP 65.86(3)(g)
(g)
Calibration and daily performance check samples; total solids. ATCP 65.86(3)(g)1.1. The provider of a calibration sample under par.
(b) or a daily performance check sample under par.
(c) shall determine the known percentage content of total solids in that sample by averaging the results of 3 total solids tests using the method specified under subd.
3. The percentage total solids results from those 3 tests shall not vary by more than 0.054 percentage points.
ATCP 65.86(3)(g)2.
2. The known total solids content of a calibration or daily performance check sample, expressed as a percentage of sample weight, shall be at least 11%. Within a set of calibration samples, the difference in known total solids content between the lowest total solids sample and the highest total solids sample, expressed as a percentage of average sample weight, shall be at least 2.00%. Within a set of daily performance check samples, the difference in known total solids content between the lowest total solids sample and the highest total solids sample, expressed as a percentage of average sample weight, shall be at least 1.5%.
ATCP 65.86(3)(g)3.
3. To determine the total solids content of a calibration sample or daily performance check sample, the sample provider shall use the direct forced air oven drying method as described in the “Official Methods of Analysis of AOAC International," 18th edition (2005), section 990.20.
ATCP 65.86 Note
Note: The “Official Methods of Analysis of AOAC International," 18th edition (2005), is on file with the division and the legislative reference bureau, and may be obtained from AOAC International, 2275 Research Blvd., Rockville, MD 20850, website
https://www.aoac.org .
ATCP 65.86(3)(h)
(h)
Calibration and daily performance check samples; solids-not-fat. The provider of a calibration sample under par. b or a daily performance check sample under par.
(c) shall calculate the known percentage content of solids-not-fat in that sample by subtracting the percent milkfat as determined under par.
(e) from the total solids for that sample as determined under par.
(g). The calculation method shall be that described in the “Official Methods of Analysis of AOAC International," 18th edition (2005), section 990.21.
ATCP 65.86 Note
Note: The “Official Methods of Analysis of AOAC International," 18th edition (2005), is on file with the division and the legislative reference bureau, and may be obtained from AOAC International, 2275 Research Blvd., Rockville, MD 20850, website
http://www.aoac.org .
ATCP 65.86(3)(i)
(i)
Automated testing devices; constant voltage. A constant voltage regulator shall be connected to, or form a part of, every milk component testing device that is in line with a single phase 115 or 220-volt power supply.
ATCP 65.86(3)(j)
(j)
Records related to calibrations, daily performance checks, and reference checks. ATCP 65.86(3)(j)1.
1. A dairy plant operator shall keep a record of every calibration, performance check, or reference check conducted on a milk component testing device under this section.
ATCP 65.86(3)(j)2.
2. Every record required under subd. 1 shall be signed by the licensed tester who made the record. Calibration records shall be kept separate from performance check and reference check records.
ATCP 65.86(3)(k)
(k)
Accuracy of devices; division audit. The division may audit the accuracy of milk component testing devices using test samples prepared by the division under pars.
(e) to
(h).
ATCP 65.86 History
History: CR 14-073: cr.
Register August 2016 No. 728, eff. 9-1-16; correction in (3) (c) 3. made under s.
35.17, Stats.,
Register August 2016 No. 728.
ATCP 65.910
ATCP 65.910 Inspection of dairy farms; general. ATCP 65.910(1)(1)
Inspection by dairy plant operator. Before a dairy plant operator, including a milk contractor that submits a milk producer license application on behalf of a milk producer and thereby certifies that the milk producer's dairy farm and milking operations comply with applicable requirements under this chapter, submits a milk producer license application or a grade A permit application under s.
ATCP 65.02 on behalf of a milk producer, the dairy plant operator shall inspect the dairy farm for compliance with the dairy farm standards under subch.
II. The dairy plant operator, when submitting the producer's license or permit application, shall include a copy of the dairy plant operator's inspection report and shall certify that the dairy farm facilities comply with dairy farm standards under subch.
II. The department may, at other times, require a dairy plant operator to inspect a dairy farm as necessary.
ATCP 65.910(2)
(2) Inspection by the division. The division shall inspect dairy farms for compliance with dairy farm standards under subch.
II. The division shall inspect a grade A dairy farm at the frequency given in s.
ATCP 65.912 and a grade B dairy farm at least once every year. For the purpose of conducting a lawful inspection under this chapter, the department may exercise its authority under ss.
93.08,
93.15 (2), and
97.12 (1), Stats.
ATCP 65.910(3)
(3) Variances. The division administrator, or the division administrator's designee, may issue a written waiver granting a variance from a dairy farm standard under subch.
II if the division determines that the variance is reasonable and necessary under the circumstances, it will not compromise the purpose served by the standard, and the milk producer does not hold a grade A farm permit.
ATCP 65.910 History
History: CR 14-073: cr.
Register August 2016 No. 728, eff. 9-1-16.
ATCP 65.912
ATCP 65.912 Performance-based grade A dairy farm inspections. ATCP 65.912(1)(1)
General. The division shall use the performance standards in this section to determine grade A dairy farm inspection frequency. The division shall evaluate each grade A dairy farm every 3 months, on the basis of information including inspection reports, milk quality tests, and department compliance actions taken during the preceding 12 months. As provided in subs.
(2) to
(5), the division shall place each dairy farm in one of the following categories:
ATCP 65.912(2)
(2) Twelve-month inspection interval. The division shall inspect a grade A dairy farm in the twelve-month inspection interval category at least once every 12 months. The division shall place a dairy farm in this category if all the following apply, based on dairy farm inspection reports, milk quality tests, and department compliance actions, during the preceding 12 months:
ATCP 65.912(2)(a)
(a) None of the milk producer's reported standard plate count (SPC) results exceed 25,000 per ml., except that one reported SPC result may exceed 25,000 per ml. if it is not more than 100,000 per ml.
ATCP 65.912(2)(b)
(b) None of the milk producer's reported somatic cell count (SCC) results exceed 500,000 per ml.
ATCP 65.912(2)(d)
(d) No dairy farm inspection report shows more than 5 violations, a violation observed during consecutive inspections, a violation that creates a substantial risk of adulteration, or a violation that creates an imminent health hazard.
ATCP 65.912(2)(e)
(e) The department has not suspended the producer's grade A dairy farm permit or milk producer license.
ATCP 65.912(2)(g)
(g) The milk producer has not violated any milk temperature or cooling standards under this chapter.
ATCP 65.912(3)
(3) Six-month inspection interval. The division shall inspect a grade A dairy farm in the six-month inspection interval category at least once every 6 months. The division shall place a dairy farm in this category if all the following apply, based on dairy farm inspection reports, milk quality tests, and department compliance actions, during the preceding 12 months:
ATCP 65.912(3)(d)
(d) No dairy farm inspection report shows more than 5 violations, a violation observed during consecutive inspections, a violation that creates a substantial risk of adulteration, or a violation that creates an imminent health hazard.
ATCP 65.912(3)(e)
(e) The department has not suspended the producer's grade A dairy farm permit or milk producer license.
ATCP 65.912(3)(g)
(g) The milk producer has not violated any milk temperature or cooling standards under this chapter.
ATCP 65.912(4)(a)
(a) The division shall inspect a grade A dairy farm in the four-month inspection interval category at least once every 4 months. The division shall place a dairy farm in this category if subs.
(2),
(3), and
(5) do not apply and if any of the following apply based on dairy farm inspection reports, milk quality tests, and department compliance actions, during the preceding 12 months:
ATCP 65.912(4)(a)1.
1. At least one load of milk shipped by the milk producer has been found to contain a drug residue.
