ATCP 65.08(1)(1)
Requirement. Every dairy farm shall have a milkhouse. Except as provided in s.
ATCP 65.16 (5), a milk producer shall cool and store milk in the milkhouse. A milkhouse shall be separate from a milking barn or parlor, but may share common walls with a milking barn or parlor. All milking equipment and utensils shall be cleaned, sanitized and stored in the milkhouse, except for C-I-P milk pipelines that are mechanically cleaned in place in a milking barn or parlor, or C-I-P milking equipment that is mechanically cleaned and stored in a milking parlor under s.
ATCP 65.06 (10) (a).
ATCP 65.08(2)
(2) Access to Milkhouse. Every access driveway and every exterior access door to the milkhouse shall be located in such a manner that no vehicle or a person traveling to the milkhouse must pass through an animal walkway, holding area, or yard where excessive animal waste may accumulate on the ground near these access areas.
ATCP 65.08(3)(a)
(a)
Floors. A milkhouse floor shall be constructed of concrete or one or more other impervious materials, and shall be easily cleanable. This requirement does not prohibit construction with anti-slip floor surfaces that are easily cleanable. The floor shall be sloped for drainage to a floor drain. Floor drains shall be readily accessible. A floor drain shall be equipped with a trap if the floor drain is connected to a sanitary sewer system.
ATCP 65.08(3)(b)
(b)
Walls and ceilings. Milkhouse walls and ceilings shall be constructed and finished so that they are impervious to water, are light colored, and are easily cleanable.
ATCP 65.08(3)(c)
(c)
Doors and windows. A milkhouse shall not open directly into a barn, stable or milking parlor, or into a room not used for the operation of the dairy farm unless the opening is equipped with a tight-fitting, self-closing and solid door. All milkhouse external openings shall be screened or otherwise protected against entry of insects, rodents, or other pests. External doors and windows shall be tight-fitting and shall be kept closed during dusty conditions. External doors shall be self-closing. All swinging screen doors on the milkhouse shall open outward.
ATCP 65.08(3)(d)
(d)
Lighting. Natural or artificial lighting, or both, shall be provided in a milkhouse to ensure adequate illumination for daytime and nighttime operations. There shall be at least 30 foot-candles of illumination in all working areas of the milkhouse. Artificial lights located over a bulk tank shall be shatterproof or shielded to protect milk from contamination with broken glass.
ATCP 65.08(3)(e)
(e)
Ventilation. Ventilation in a milkhouse shall be adequate to minimize odors and to prevent visible condensation on floors, walls, ceilings, clean equipment, and clean utensils. Vents shall be screened and shall be located and maintained to prevent contamination of bulk tanks or clean equipment and utensils. Exhaust fans shall be screened or louvered to prevent entry of pests when not in operation. Ventilation in an AMI room shall be sufficient to minimize odors from any nearby manure storage.
ATCP 65.08(3)(f)
(f)
Water heating capacity. Hot water capacity shall be adequate for all milkhouse operations. Hot water heaters or hot water supply systems shall have a capacity of at least 10 gallons for washing equipment and utensils. The division may authorize alternative systems, including heat recovery and continuous flow systems that provide adequate hot water for all milkhouse operations. Authorization shall be in writing and valid for 5 years. Re-authorization for each subsequent 5-year period shall be obtained in writing from the division.
ATCP 65.08(3)(g)
(g)
Wash and rinse vat. A milkhouse shall be equipped with a 2-compartment wash and rinse vat for cleaning equipment and utensils. The vat shall be served by potable hot and cold running water from a faucet or faucets located directly over the vat. Water shall enter and leave the vat by means that preclude splashing. A vat designed to hold cleaning or sanitizing solutions drawn through C-I-P milking equipment may serve as one compartment of a two-compartment wash and rinse vat under this paragraph, provided that the C-I-P inflation rack and all C-I-P milking equipment are completely removed from the vat while other equipment and utensils are being washed, rinsed, and sanitized in the vat. This paragraph shall apply to an AMI for which manual cleaning and sanitizing of AMI components must be done on a routine basis.
ATCP 65.08(3)(h)
(h)
Handwashing facility. A milkhouse shall be equipped with a fixed hand washing facility that is separate from the wash and rinse vat under par.
(g). The hand washing facility shall be served by potable hot and cold running water from a faucet or faucets located directly over the facility. Water shall enter and leave the handwashing facility by means that preclude splashing. Soap and single service sanitary towels or another approved means of drying hands shall be available at all times for use at the hand washing facility. A hand washing facility may be located in a room immediately adjacent to the milkhouse, provided that it is readily accessible from the milkhouse. This paragraph applies to an AMI room in which the operator's hands will contact milk filters or other milk contact surfaces. This paragraph does not apply to licensed milk producers who do not hold a grade A producer permit but operate a dairy farm on which the currently used bulk tank was installed before January 1, 1979, or on which milk is stored and cooled only in cans.
ATCP 65.08(3)(i)
(i)
Bulk tank hose port. If a bulk tank is used to receive and hold milk in a milkhouse, the milkhouse shall have a hose port opening in the outside wall to permit the removal of milk from the bulk tank. The hose port opening shall be at least 6 inches above the floor of the milkhouse, and shall be equipped with a tight-fitting door that shall be kept closed except when the hose port is in use. A paved surface of concrete or other readily cleanable material shall be installed adjacent to the outside wall of the milkhouse, immediately under the bulk tank hose port. The paved surface shall be at least a 4 foot by 4 foot square and shall cover as much additional ground area as is necessary to protect the milk hose from ground contamination.
ATCP 65.08(4)
(4) Maintenance and sanitation. The floors, walls, ceilings, windows, hose port assembly, and all equipment of a milkhouse shall be kept clean and in a good state of repair. Liquid wastes from milkhouse operations shall be drained and removed in a sanitary manner. Equipment and utensils shall be cleaned and maintained in compliance with s.
ATCP 65.12. A milkhouse shall be kept free of insects, rodents, and other pests. Animals shall be kept out of the milkhouse at all times. Potential sources of milk contamination, including materials that may attract or harbor pests, shall be excluded from the milkhouse.
ATCP 65.08(5)(a)
(a)
General. No equipment, supplies, or other articles may be stored in a milkhouse, unless the articles are used in milkhouse operations. Articles stored in a milkhouse shall be stored above the floor, on racks, or in a cabinet. Articles shall be stored in a manner that prevents both the contamination of milk and contact of equipment or utensils with milk. Washing machines, laundry dryers, and pasteurizers used to prepare milk-replacement formula for calves shall not be stored in the milkhouse.
ATCP 65.08(5)(b)
(b)
Drugs and medicinal items. No drug or medicinal item, or drug administering device such as a bolus wand or syringe, may be kept in a milkhouse unless it is intended or prescribed for use on dairy animals. If drugs or medicinal items are kept in a milkhouse, they shall be stored in an enclosed cabinet, separate from all other articles stored in the milkhouse. Drugs and medicinal items shall be clearly labeled to indicate their identity and intended use, and prescription drugs shall be labeled as provided under s.
ATCP 65.20 (5). Drugs and medicinal items intended solely for treatment of non-lactating milking animals shall be kept separate from those used for treatment of lactating milking animals.
ATCP 65.08(5)(c)
(c)
Pesticides. No pesticides, except for sanitizers, germicides, disinfectants, or pesticides labeled and used for routine milkhouse sanitation purposes, may be stored in a milkhouse. Any of the chemicals labeled for routine use in a milkhouse must be stored in a manner that precludes contamination of milk and milk handling equipment.
ATCP 65.08 History
History: CR 14-073: cr.
Register August 2016 No. 728, eff. 9-1-16.
ATCP 65.10(1)(1)
General. An adequate supply of potable water shall be supplied under pressure for milkhouse and milking operations. Water used for milkhouse and milking operations, including water used to cool milk in a plate or tubular cooler, shall be potable. Potable water shall comply with the microbiological drinking water standards set forth in s.
NR 809.30.
ATCP 65.10 Note
Note: A properly designed and installed water supply tank that utilizes static head pressure to provide potable running water to the milkhouse is minimally adequate to comply with this paragraph.
ATCP 65.10(2)
(2) Backflow protection; cross-connections. A potable water supply system on a dairy farm shall be designed, constructed, installed, and maintained to prevent contamination of the potable water supply through backflow, backsiphonage, cross-connections, or any other connection to the potable water supply system. An air gap adequate to prevent the back-siphonage or backflow of any liquids shall be maintained between every potable water outlet and the flood rim of the fixture that it supplies, and between the potable water outlet and every other source of potential contamination, unless alternative protection is approved under s.
SPS 382.41.
ATCP 65.10(3)
(3) Well construction. Wells used to supply water for milkhouse and milking operations on dairy farms shall comply with ch.
NR 810,
811, or
812 in the case of a community water system.
ATCP 65.10(4)
(4) Water transported to dairy farm. A person transporting water in containers or tanks to a dairy farm for milkhouse or milking operations shall seal the containers or tanks to prevent contamination. The containers and tanks shall be thoroughly cleaned and sanitized before being filled with potable water for use at the dairy farm. A sanitarily designed, cleaned, and sanitized pump, hose, and fittings shall be used to transfer water from transport containers and tanks to previously cleaned and sanitized storage tanks at the dairy farm so that the water is not contaminated during transfer or by the storage tanks.
ATCP 65.10(5)
(5) Water quality testing by dairy plant. A dairy plant operator, including a milk contractor that submits a milk producer license application on behalf of a milk producer and thereby certifies that the milk producer's dairy farm and milking operations comply with applicable requirements under this chapter, shall do all of the following for each milk producer from whom the dairy plant operator procures milk:
ATCP 65.10(5)(a)
(a) Sample the milk producer's water supply at least once every two years. If the water supply system has more than one well, water from each well shall be sampled. The water sample from each well shall be taken from water before it has flowed into a pressure tank or any water treatment equipment.
ATCP 65.10(5)(b)
(b) Sample the milk producer's water supply whenever the milk producer installs, alters, or repairs the water supply system.
ATCP 65.10(5)(c)
(c) Sample any transported water supply used by the milk producer at the point of use, at or before first use and monthly thereafter.
ATCP 65.10(5)(d)
(d) Have each water sample under this subsection analyzed at a laboratory that is certified under ch.
ATCP 77 to perform water quality analyses. The laboratory shall analyze the water samples for compliance with the microbiological drinking water standards set forth in s.
NR 809.30. The dairy plant operator shall submit each water quality analysis result to the division within 30 days after the dairy plant receives the water quality analysis result. If the analysis of any water sample indicates that the water supply of a dairy farm may be unsafe, the dairy plant operator, within 3 business days of the water quality analysis result being reported to the dairy plant operator, shall report the analysis result to the division and resample the water supply and have it analyzed.
ATCP 65.10(6)(a)
(a) A milk producer may use re-circulated water in a plate cooler to cool milk on a dairy farm if all of the following apply:
ATCP 65.10(6)(a)4.
4. The coolant used in the water recirculation system is non-toxic food or pharmaceutical grade propylene glycol meeting the specifications in
21 CFR 184.1666, and does not contain coliform bacteria as determined by sampling and analysis done at least semi-annually by the dairy plant operator.
ATCP 65.10(6)(a)5.
5. The dairy plant operator who procures milk from the milk producer tests the recirculated water for coliform bacterial contamination at least semi-annually.
ATCP 65.10(6)(b)
(b) If a recirculating water system, under par.
(a), becomes contaminated, the milk producer shall stop using the system until all the following conditions are met:
ATCP 65.10(6)(b)1.
1. The milk producer eliminates the contamination source and treats the recirculated water to make it potable.
ATCP 65.10(6)(b)2.
2. The dairy plant operator who procures milk from the milk producer retests the recirculated water to determine whether the contamination is eliminated.
ATCP 65.10(6)(b)3.
3. Retesting shows that the recirculated water complies with the bacteriological standards under par.
(c).
ATCP 65.10(6)(c)
(c) Recirculated water shall meet all the following bacteriological test standards:
ATCP 65.10(6)(c)1.
1. The most probable number (MPN) of coliform organisms shall be less than 1.1 per 100 ml. as determined using the multiple tube fermentation technique, or less than 1.0 per 100 ml. as determined using the membrane filter technique.
ATCP 65.10(6)(c)2.
2. Bacteriological testing using the membrane filter technique shall show not more than 200 total bacterial colonies per 100 ml.
ATCP 65.10(6)(c)3.
3. Bacteriological testing using a heterotrophic plate count technique shall show not more than 500 colonies per ml.
ATCP 65.10(7)(a)(a) Water reclaimed from a heat exchanger, may be used for milkhouse and milking operations, including cooling milk in a plate or tubular cooler, if all of the following conditions are met:
ATCP 65.10(7)(a)1.
1. The water is stored in a cleaned and sanitized vessel that is constructed of non-contaminating materials and is designed to protect the water supply from contamination. The storage vessel shall have a drain and access point that allow for cleaning and sanitizing.
ATCP 65.10(7)(a)2.
2. There is no cross-connection between the reclaimed water and any potential contamination source or potentially unsafe water supply.
ATCP 65.10(7)(a)3.
3. There are no submerged inlets through which the reclaimed water may be contaminated.
ATCP 65.10(7)(a)6.
6. The dairy plant operator who procures milk from the milk producer collects and analyzes samples of the reclaimed water supply before the milk producer first uses the water for milkhouse and milking operations, and at least semi-annually thereafter.
ATCP 65.10(7)(a)7.
7. Any chemicals used to suppress bacterial growth, tastes, and odors are registered for that use with the U.S. environmental protection agency. Milk processed in or exposed to any system using chemicals to suppress bacterial growth, tastes, and odors shall not be allowed to become contaminated with those chemicals. A milk producer who uses any chemical to suppress bacterial growth, tastes, or odors shall comply with the chemical label use instructions, and shall routinely monitor chemical concentrations in treated water.
ATCP 65.10(7)(a)8.
8. Sanitizers used to sanitize equipment, utensils, teats of milking animals, or to backflush systems, shall be chemical sanitizers that comply with
21 CFR 178.1010, are registered with the U.S. environmental protection agency, and are thereby suitable for use on food contact surfaces. An approved sanitizer may be added by an automatic metering device that is located downstream from the storage vessel but upstream from the end-use application of the sanitizer.
ATCP 65.10(7)(b)
(b) Water obtained directly from the discharge of an unpasteurized milk heat exchanger after a milking may be used once to pre-rinse dairy equipment including milk lines, milking claw assemblies, and milk receivers if all of the following apply:
ATCP 65.10(7)(b)1.
1. The water is collected directly from the heat exchanger into a cleaned and sanitized wash vat or utensil sink.
ATCP 65.10 Note
Note: Paragraph (b) does not prevent the use of heat exchanger discharge water for non-potable uses involving no contact with potable water, milk, milk contact surfaces or potable water contact surfaces. Before using or discharging heat exchanger discharge water, contact the Division of Water, Bureau of Drinking Water and Ground Water, at the Department of Natural Resources, P.O. Box 7921, Madison, WI 53707, telephone 608-266-0821 or TTY access via relay — 711 or
http://www.dnr.state.wi.us/environmentprotect/water.html.
ATCP 65.10(8)
(8) Water reclaimed from sources other than a heat exchanger. Water reclaimed from a compressor cooling unit, manure treatment, or from other dairy farm systems or processes may be used as non-potable water for milking barn or parlor operations, not to include rinsing, cleaning and sanitizing of milking systems, if all of the following conditions are met:
ATCP 65.10(8)(a)
(a) The water is reclaimed by means of evaporation, reverse osmosis, ultra-filtration, or another method approved by the division.
ATCP 65.10(8)(b)
(b) The water is stored in a cleaned and sanitized vessel that is constructed of non-contaminating materials and is designed to protect the water supply from contamination. The storage vessel shall have a drain and access point that allow for cleaning and sanitizing.
ATCP 65.10(8)(c)
(c) There is no cross-connection between the reclaimed water and potable water supplies or between the reclaimed water and any potential contamination source or potentially unsafe water supply.
ATCP 65.10(8)(d)
(d) There are no submerged inlets through which the reclaimed water may contaminate the potable water system.
ATCP 65.10(8)(e)
(e) Any chemicals used to suppress bacterial growth, tastes, and odors are registered for that use with the U.S. environmental protection agency. A milk producer who uses any chemical to suppress bacterial growth, tastes, or odors shall comply with the chemical label use instructions, and shall routinely monitor chemical concentrations in the treated water.
ATCP 65.10 History
History: CR 14-073: cr.
Register August 2016 No. 728, eff. 9-1-16; correction in (6) (a) 1., (7) (b) 2. made under s.
35.17, Stats.,
Register August 2016 No. 728.
ATCP 65.12(1)(1)
Construction; general. Equipment and utensils shall be constructed of smooth, non-absorbent, corrosion-resistant, and non-toxic materials. Equipment and utensils shall be designed and constructed so that they can be easily cleaned and shall be durable under repeated conditions of use. Surfaces shall be free of breaks and corrosion. Joints and seams shall be smooth and flush. Milk pails used for hand milking and stripping shall be seamless. Multiple-use woven material shall not be used for straining milk. Milking and milk handling systems shall comply with s.
ATCP 65.14.
ATCP 65.12(2)
(2) Milk contact surfaces; construction. Milk contact surfaces of equipment and utensils shall be constructed of smooth, non-toxic, and non-absorbent materials. Only the following materials may be used on milk contact surfaces, unless another material is specifically authorized by the division in writing:
ATCP 65.12(2)(a)
(a) Stainless steel of the American Iron and Steel Institute 300 Series, or an equally corrosion-resistant metal.
ATCP 65.12(2)(c)
(c) Plastic, rubber, or rubber-like materials that are fat resistant and insoluble; that are resistant to scratching, scoring, decomposition, crazing, chipping, and distortion under normal use conditions; that do not impart chemicals, flavor, or odor to milk; and that maintain their original properties under repeated and prolonged use.
ATCP 65.12(3)
(3) Maintenance. Equipment and utensils shall be kept in good repair and shall be readily accessible for inspection by the division upon request.
ATCP 65.12(4)
(4) Cleaning. Equipment and utensils shall be kept clean. Utensils and milk contact surfaces of equipment shall be rinsed immediately after each use and then washed with an effective detergent and rinsed clean. C-I-P equipment shall be pre-washed with warm water before being cleaned with a detergent solution, according to manufacturer's instructions.
ATCP 65.12(5)
(5) Sanitizing. After being cleaned and rinsed, utensils, and milk contact surfaces of equipment shall be sanitized before being used.
ATCP 65.12(6)
(6) Storage. Equipment and utensils, unless stored in sanitizing solutions, shall be handled and stored in a manner that will ensure complete drainage and protection from contamination before use. Equipment and utensils stored in sanitizing solutions shall be rinsed in potable water before use.
ATCP 65.12(7)
(7) Single service articles. Single-service articles shall be clean and sanitary, and shall be packaged, handled, and stored in a sanitary manner. Single-service articles shall be stored in their original containers inside a dispensing cabinet. Single service articles may not be reused.
ATCP 65.12 History
History: CR 14-073: cr.
Register August 2016 No. 728, eff. 9-1-16.
ATCP 65.14
ATCP 65.14
Milking and milk handling systems. ATCP 65.14(1)(1)
Sanitary requirements; general. Milking and milk handling systems shall be of sanitary design and construction, and shall be installed and maintained for sanitary operation. Pressurized air that contacts a milk or milk contact surface shall be clean, safe, and free of contaminants. The milking and milk handling system shall comply with “3-A Accepted Practices for the Design, Fabrication and Installation of Milking and Milk Handling Equipment, 606-05." Milk contact surfaces shall be accessible for inspection. If it is necessary to disassemble any portion of a milking or milk handling system in order to inspect a milk contact surface, all tools necessary for the disassembly shall be readily available in the milkhouse.
ATCP 65.14 Note
Note: Guidelines for sanitary design and construction of milking and milk handling systems are set forth in the "3-A Accepted Practices for the Design, Fabrication and Installation of Milking and Milk Handling Equipment," 606-05, as amended effective November 2002, published by 3-A Sanitary Standards, Inc., 6888 Elm Street, Suite 2D, McLean, VA 22101-3850, telephone (703) 790-0295, website
www.3-a.org. Milking and milk handling systems manufactured in compliance with the "3-A Accepted Practices" meet the sanitary design and construction requirements of this subsection. Copies of the "3-A Accepted Practices" are on file with the division and the legislative reference bureau. Copies may be obtained from 3-A Sanitary Standards, Inc. Online Store," at
http://www.techstreet.com.
ATCP 65.14(2)
(2) Milk contact surfaces; construction. Milk contact surfaces of milking and milk handling systems shall be constructed of smooth, nontoxic, and nonabsorbent materials. Materials shall be of any of the following types, unless another material is specifically authorized by the division in writing:
ATCP 65.14(2)(a)
(a) Stainless steel of the American Iron and Steel Institute 300 series, or an equally corrosion resistant metal.
ATCP 65.14(2)(c)
(c) Plastic, rubber, or rubber-like materials that are fat resistant and insoluble; that are resistant to scratching, scoring, decomposition, crazing, chipping, and distortion under normal use conditions; that do not impart chemicals, flavor or odor to milk; and that maintain their original properties under repeated use conditions.
ATCP 65.14(3)(a)
(a) Milk contact surfaces of permanently mounted milk pipelines shall be constructed of stainless steel or an equally non-toxic, corrosion resistant metal, or of heat resistant glass. Plastic or rubber-like materials may be used for pipeline gaskets, connections, and sealing applications, but not for other purposes. Paper gaskets are prohibited.
ATCP 65.14(3)(b)
(b) All joints of permanently mounted milk pipelines, including joints in solution lines, shall be welded or equipped with fittings designed for C-I-P. Welded joints shall be smooth and free of pits, cracks, or other defects. Removable fittings shall be designed to form substantially flush interior joints.
ATCP 65.14(3)(c)
(c) Permanently mounted pipelines shall be supported at intervals of not more than 10 feet so that the pipelines remain in constant alignment and position. Permanently mounted pipelines shall be self-draining, and shall have a minimum slope of one inch per 10 feet. The support system shall be designed and constructed to prevent electrolytic reactions between supports and pipelines.
