Trans 313.08(1)(1) Modifications. A manufacturer shall meet all of the following requirements: Trans 313.08(1)(a)(a) Notify the department in writing of any material modification in the components, design or installation and operating instructions of any device approved for use in this state. For purposes of this paragraph, a modification shall be considered material if the modification affects device operation or functionality. Trans 313.08(1)(b)(b) Provide the department satisfactory proof that modifications or alterations for which notice is provided under par. (a) do not adversely affect the ability of the device to satisfy the requirements of s. Trans 313.04. Trans 313.08(1)(c)(c) Upon the department’s request, provide any new or updated materials related to quality assurance of the calibration procedure and device calibration checks provided under s. Trans 313.04 (2) (b) 13. Trans 313.08(1)(d)(d) Upon the department’s request, provide sample modified devices the department may inspect or test for continued acceptability under this chapter. Trans 313.08(2)(2) Manufacturer approved repair facilities. A manufacturer shall provide for the repair of the internal components of handsets and vehicle modules through its own technicians or a manufacturer-approved authorized device repair facility. Trans 313.08 NoteNote: Manufacturer-approved authorized device repair facilities shall demonstrate the technical competence to repair handsets and vehicle modules as a condition of device approval. See s. Trans 313.04 (2) (b) 8. Trans 313.08(3)(3) Mouthpieces. A manufacturer or vendor shall make an adequate supply of mouthpieces or other replaceable breath receptor devices available to a service provider. Trans 313.08(4)(4) Anti-tampering. A manufacturer shall ensure that a device has adequate electronic anti-tampering features which include all of the following: Trans 313.08(4)(a)(a) A device shall retain its tamper detection capabilities when disconnected from the vehicle’s power supply, or record that it was disconnected. Trans 313.08(4)(b)(b) A device shall retain its data memory when disconnected from the vehicle’s power supply. Trans 313.08(4)(c)(c) When a device detects a condition that would be considered tampering, the device shall activate a visual and audible indicator. Trans 313.08 NoteNote: Detected tampering must be reported, and evidence retained under s. Trans 313.105 (7). Trans 313.08(5)(a)(a) For each device model a manufacturer or vendor seeks to have approved under s. Trans 313.04, upon the department’s request, the device manufacturer or vendor shall provide a total of at least 10 hours of training to the department’s employees at no cost to the State of Wisconsin. For each device that is approved by the department, upon the department’s request, the device manufacturer or vendor shall provide ongoing training. The manufacturer or vendor shall hold training sessions at reasonable times and locations within the State designated by the department. The training shall familiarize the department’s employees with the installation, operation, service, repair and removal of the devices and with the training and instructions that the manufacturer or vendor will give to service providers and customers. The manufacturer or vendor shall also provide the department, upon request, all materials intended for distribution to service providers or customers related to installation, operation, repair or removal of the device. Trans 313.08(5)(b)(b) The manufacturer or vendor shall loan the department, free of charge, a demo unit for each approved device that department personnel may use for training staff, court officials, law enforcement officers, or others. The manufacturer or vendor shall provide service for the loaned device free of charge at the chemical testing section Madison office or at the closest service center thereto. Trans 313.08(5)(c)(c) The manufacturer or vendor shall develop device installation instructions for service provider use and share them with the department upon request. Trans 313.08(6)(6) Disabling a lockout. A manufacturer or vendor may provide a lockout code for the purpose of disabling a lockout event in accordance with s. Trans 313.04 (5) (i). Trans 313.08 HistoryHistory: Cr. Register, August, 1993, No. 452, eff. 9-1-93; CR 20-020: r. and recr. Register September 2021 No. 789, eff. 10-1-21. Trans 313.09(1)(1) In order to ensure that devices are available to persons in all areas of the state, as a condition of approval and use in the state of Wisconsin, each device must include an affirmation from the device manufacturer, vendor of the device, or a service provider that it will agree to take assignments to unserved areas of the state of Wisconsin in accordance with this section. Trans 313.09(2)(2) The department shall monitor the service center sites throughout Wisconsin. If the department determines that any place in Wisconsin is not within 75 miles of a fixed, permanent service center, the department shall randomly select one of the entities that made an affirmation under sub. (1) and require that entity to establish a service center or provide a mobile service center in the unserved area. If a second or subsequent area of Wisconsin is determined not to be within 75 miles of a fixed, permanent service center, the department shall randomly select an entity that made an affirmation under sub. (1) other than the ones selected previously and require that entity to establish a service center or provide a mobile service in the unserved area. If all entities that make affirmations under sub. (1) have been required to provide service centers under this subsection, the process of randomly selecting entities shall be repeated. Trans 313.09(3)(3) A manufacturer or vendor shall notify the department in writing at least 7 days before a fixed, permanent service center closes or a fixed, permanent service center moves to another address. In the event a fixed, permanent service center moves, the manufacturer or vendor shall provide the department with the address of the new fixed, permanent service center location or notice that service to the area of the fixed, permanent service center will be provided by a mobile service center at least 7 days before the scheduled service center move. In the event of an emergency, such as a flood, fire, riot, or weather-related event affects a service center, the manufacturer or vendor shall provide the department with notice of the effect of the emergency event on the service center and its plans for re-establishing service at that location or moving the service center to a new location as soon as reasonably possible. Trans 313.09(4)(4) A manufacturer or vendor shall provide the department with at least 7 days’ advance notice of discontinuing mobile service to any part of the state. Service may not be discontinued to any location assigned to an affirmant under sub. (2) unless the affirmant can show that a different entity is providing service in that area. Trans 313.09 NoteNote: Under s. Trans 313.07 (1) (h), device approval for use in the state of Wisconsin may be revoked, suspended or denied if an entity that made a service provider affirmation under sub. (1) fails to provide reasonable service in an area assigned to the service provider under sub. (2). Trans 313.09 HistoryHistory: Cr. Register, August, 1993, No. 452, eff. 9-1-93; CR 20-020: r. and recr. Register September 2021 No. 789, eff. 10-1-21; correction in (4) made under s. 35.17, Stats., Register October 2022 No. 802. Trans 313.10(1)(a)(a) A service center shall inspect and calibrate a device when it is installed to ensure that it is functioning properly, reliably and accurately. Trans 313.10(1)(b)(b) A service center shall conduct tamper inspections any time that a device is serviced. Tamper inspections include all of the following: Trans 313.10(1)(b)1.1. Inspection of all external wiring insulation, connections, and sheathing for the device and locations where the device connects to the vehicle. Trans 313.10 NoteNote: Detected tampering must be reported and evidence retained under s. Trans 313.105 (7). Trans 313.10(1)(b)2.2. Documentation of any electronic indications of tampering to the device’s memory record. Trans 313.10(1)(b)3.3. Inspection of all tamper seals for breaks, tears or other evidence of tampering. Trans 313.10(1)(c)(c) A service provider shall cause all of its service centers to have all the tools, test equipment and manuals needed to service devices and shall perform basic troubleshooting related to device installation and operation. Trans 313.10(2)(2) Service locations and hours. A manufacturer, vendor or service provider that makes an affirmation under s. Trans 313.09 (1) shall provide the following minimum service: Trans 313.10(2)(a)(a) Repair or replace the device within 3 days after service is requested. Trans 313.10(2)(b)(b) A reasonable number of service centers within the state. If a service provider has a fixed, permanent service center, it may install and service devices using mobile service centers in this state in accordance with s. Trans 313.10 (11). Service centers must establish and maintain reasonable business hours. Trans 313.10(2)(c)(c) A 24-hour toll-free telephone number to answer questions, and to deal with mechanical problems and emergencies related to the device. Trans 313.10 NoteNote: Nothing in this paragraph is intended to prohibit a manufacturer, vendor or service provider from providing additional alternative communication mechanisms. Explanation of responsibility for responding to telephone inquiries and other communications is required as part of an application filed under s. Trans 313.04 (2) (b) 20. Trans 313.10(3)(3) Security. A service provider shall comply with all of the following security requirements: Trans 313.10(3)(a)(a) Only authorized employees of a service provider, manufacturer or the department may observe the installation of a device. Reasonable security measures must be taken to prevent the customer from observing the installation of a device, or obtaining access to installation materials. Trans 313.10(3)(b)(b) A service provider is prohibited from assisting or facilitating any tampering, circumvention or bypass of a device. Trans 313.10(3)(c)(c) A service provider may not install a device on a vehicle owned or operated by any of its employees. Trans 313.10(3)(d)(d) A service provider shall install any security device provided by the manufacturer. Trans 313.10(3)(e)(e) A service provider may not access or alter the internal components of a handset or vehicle module. Trans 313.10 NoteNote: Internal repairs of handsets and vehicle modules are performed by the manufacturer or a approved manufacturer-approved authorized device repair facility.
Trans 313.10(4)(4) Installation. A service center shall comply with all of the following installation service requirements: Trans 313.10(4)(a)(a) Installation of a device must be completed within 10 days of a customer request, unless the customer requests scheduling installation at a later date or fails to provide the service center with access to the vehicle as scheduled within the 10-day period. Trans 313.10(4)(b)(b) A service center shall inspect each vehicle before installing the device. The inspection must include screening procedures to ensure the vehicle in which the device is to be installed is in a mechanical and electrical condition that will allow the device to meet the specifications in s. Trans 313.04 (5). Conditions that the manufacturer has determined would prevent the device from meeting the specifications of s. Trans 313.04 must be repaired before the device is installed. The customer shall be responsible for all the costs of any repairs to the vehicle. Trans 313.10(4)(c)(c) After a device is installed, the service center shall inspect the vehicle and device to ensure that the installation was performed properly and that it does not interfere with the normal operation of the vehicle. Trans 313.10(4)(e)(e) A service center is not required to install devices on the following types of motor vehicles: Trans 313.10(4)(e)3.3. Vehicles for which installation instructions for ignition interlock devices do not exist. Trans 313.10 NoteNote: A vehicle’s inclusion in this paragraph is not a determination as to whether a device is capable of being installed on a vehicle. See s. 343.301 (1m) (b), Stats. Trans 313.10(5)(5) Service requirements. A service provider shall be responsible for all of the following: Trans 313.10(5)(a)(a) A service provider shall follow the manufacturer’s specifications for service and repair. Trans 313.10(5)(b)(b) All devices shall be scheduled for service and calibration at intervals not to exceed 60 days. Any failure of a customer to obtain required service or calibration shall be reported to the department in the manner prescribed by the department. Trans 313.10(5)(c)(c) Each time a device is serviced, the service center shall extract the data recorded in the device’s memory, and transmit the data to the manufacturer for retention in the customer’s file and reporting to the department. Trans 313.10(6)(a)(a) Whenever a device is removed, the vehicle must be restored to its original condition. All severed wires must be securely reconnected and insulated with heat shrink tubing or its equivalent. Trans 313.10(6)(b)(b) A service provider, vendor or manufacturer shall transmit proof of installation or removal to the department in the manner prescribed by the department within 3 business days after the installation or removal of a device. Trans 313.10(7)(7) Training. A service center shall provide an orientation to the ignition interlock device to the driver and any family members or others who may drive the vehicle. The service center shall include information on all service locations, procedures for regular servicing and emergency situations, and a minimum of two successful start sequences performed by the customer in the vehicle as part of the orientation. Trans 313.10(8)(8) Mouthpieces. A service provider shall supply an adequate number of mouthpieces, breath receptors or other sample components to the customer upon initial installation and each time the device is serviced. Trans 313.10(9)(a)(a) To ensure compliance with the requirements of this section, the service provider shall make any service location and any device at the service location available for inspection by the department during the service provider’s normal business hours. Trans 313.10(9)(b)(b) The department may attend service calls made by a service center, may inspect service centers, and may audit work performed by service centers. Trans 313.10(10)(a)(a) A person shall calibrate a device using the calibration procedure for that device established by the manufacturer and approved by the department. Trans 313.10(10)(b)(b) No person may use a wet bath simulator for the calibration of any device. Trans 313.10(10)(c)(c) Calibration shall ensure that the device accurately measures alcohol concentration. A device shall be considered properly calibrated if it measures a dry gas sample at or below 0.050 g/210L within a range of ± 0.005 g/210L. Trans 313.10(11)(a)(a) All provisions of this chapter pertaining to service centers are applicable to mobile service centers. Trans 313.10(11)(b)(b) Service centers shall provide the department with a schedule for installation and calibration mobile services 24 hours before the services occur in a manner prescribed by the department. The service center shall cause the schedule to contain the name of the customer, the name of the manufacturer or vendor, the name of the service center, the location where the service will occur, and the anticipated date and time of the service. Emergency service may be provided to a customer for lockout, device or vehicle malfunction issues without advance notice under this paragraph. Trans 313.10(11)(c)(c) All mobile service centers shall be associated with a fixed, permanent service center. Trans 313.10(12)(12) Consumer disclosure. Any agreement, contract, or other document presented to a person to authorize installation of a device on a vehicle shall include all of the following information in no less than 12-point type on the front page of the documents: Trans 313.10(12)(c)(c) A description of any additional charges that may be made to the person including charges for mouthpieces, breath receptors or other sample components, if any, violation reset, maintenance, device insurance, reporting, or device calibration. Trans 313.10(12)(d)(d) The cost, if any, to be charged to person if the service provider that installs the device subsequently removes the device. Trans 313.10 HistoryHistory: Cr. Register, August, 1993, No. 452, eff. 9-1-93; CR 20-020: am. (1) (a), (b) (intro.), 1., cr. (1) (c), r. and recr. (2), (3) (e), am. (4) (intro.), (a) to (c), r. (4) (d), cr. (4) (e), am. (5) (b), (c), (6) (b), (7), (8), renum. (9) to (9) (a), cr. (9) (b), (10) to (12) Register September 2021 No. 789, eff. 10-1-21; correction in numbering in (12) made under s. 13.92 (4) (b) 1., Stats., Register September 2021 No. 789. Trans 313.105(1)(1) Calibration. A manufacturer, vendor or service provider shall follow the procedures approved by the department to calibrate a device. Trans 313.105(2)(2) Erasing data. A manufacturer, vendor or service provider shall follow the procedures approved by the department to erase any data from a device, including erasing all data from a device that is removed from a vehicle in preparation for reuse in a different vehicle. Trans 313.105(3)(3) Device configuration. A manufacturer or vendor may load approved Wisconsin device configuration files onto an approved device.
/exec_review/admin_code/trans/313
true
administrativecode
/exec_review/admin_code/trans/313/10/1/a
Department of Transportation (Trans)
administrativecode/Trans 313.10(1)(a)
administrativecode/Trans 313.10(1)(a)
section
true
