Trans 260.04(1)(1) An application for an amendment to a permit shall be made to the issuing authority which issued the original permit. Trans 260.04(2)(2) An application for an amendment may be made in the same manner as an application for an original permit. Trans 260.04(3)(3) The request shall specify the permit number of the permit to be amended. Trans 260.04(4)(4) A request for an extension of a permit may be made any time until the 3rd day after the expiration date of the permit. Trans 260.04(5)(5) An issuing authority may grant only one extension to a permit. Trans 260.04(6)(6) Except as provided in sub. (7), a permit issued for less than 2 weeks may be extended not more than 2 weeks. Trans 260.04(7)(7) An issuing authority may extend a permit not more than 2 additional weeks where highway or other conditions remain unchanged, or as the issuing authority deems necessary. Trans 260.04 NoteNote: Limitations on the amendment of permits are in s. Trans 250.10. Trans 260.04 HistoryHistory: Cr. Register, December, 1990, No. 420, eff. 1-1-91. Trans 260.05(1)(1) Any vehicle or vehicle and load to be considered as operating under a permit shall satisfy the requirements for a permit under s. 348.25, Stats. Trans 260.05(2)(2) A permit is not a guarantee of the sufficiency of any highway or structure for the transporting of the vehicle, load, or vehicle and load. Trans 260.05(3)(3) A permit may not authorize the operation of more than 2 vehicles in combination. Trans 260.05 HistoryHistory: Cr. Register, December, 1990, No. 420, eff. 1-1-91. Trans 260.06(1)(1) A permit is valid only for the route specified in the permit, which may include the return trip on the reverse route if requested and approved, and which includes the movement of the empty vehicle, whether or not oversize or overweight, to and from the place of pickup or delivery of the permitted load. Trans 260.06(2)(2) A permit may not be used in combination with a multiple trip permit to authorize the movement of an oversize load. Trans 260.06(3)(3) A permit is valid only for the vehicle described in the application and permit. Trans 260.06(4)(4) An issuing authority may suspend a permit, or any of its conditions, because of seasonal highway conditions. Trans 260.06 NoteNote: Examples of seasonal highway conditions include spring thaw, flooding, and traffic congestion.
Trans 260.06(5)(5) No condition of a permit may modify any law or regulation limiting loads because of local conditions, including load limits on bridges and highways, seasonal weight restrictions, or load limits imposed because of construction. Trans 260.06(6)(6) A permit is not valid during periods when adverse weather or road conditions, such as fog, smoke, heavy rain, snow or ice, or wind velocity, impair the safety of a movement under the permit. Trans 260.06 HistoryHistory: Cr. Register, December, 1990, No. 420, eff. 1-1-91. Trans 260.07(1)(1) A vehicle operating under a permit shall be registered as required by Wisconsin statutes, and shall be registered at not less than the permit weight or at the maximum available registration weight, whichever is less. Trans 260.07(2)(2) All other operational permits required by the department or other agencies having jurisdiction shall be obtained. Trans 260.07 HistoryHistory: Cr. Register, December, 1990, No. 420, eff. 1-1-91; correction made under s. 13.93 (2m) (b) 6., Stats., Register, August, 1996, No. 488. Trans 260.08(1)(1) The driver of a vehicle operating under a permit shall carry the permit in the vehicle to which the permit applies and shall have the permit available for inspection by any police officer, representative of the issuing authority, or person in charge of maintenance of the highway being used. Trans 260.08(2)(2) The driver of a vehicle operating under a permit shall, whenever reasonable and practicable, maintain a distance of not less than 1,000 feet between the vehicle with the permit and any vehicle the driver is following, unless actually engaged in overtaking and passing another vehicle. Trans 260.08(3)(3) The driver of a vehicle operating under a permit shall allow traffic approaching or overtaking the permitted vehicle to pass, where it is safe to do so. Trans 260.08(4)(4) Unless a lower speed is specified in the permit, a vehicle operating under a permit may be operated at the posted speed limit. Trans 260.08 HistoryHistory: Cr. Register, December, 1990, No. 420, eff. 1-1-91. Trans 260.09Trans 260.09 Maximum size and loading limitations. Trans 260.09(1)(1) A mobile home or modular building section may extend beyond the front, the left and right sides, and the rear of the undercarriage, if the overhang is minimized. Trans 260.09(2)(2) Wheels on one side of a transporting vehicle may not carry more than 60% of the total gross load. Trans 260.09(3)(3) The width authorized by a permit refers to the outside-to-outside dimension of the towed unit not including roof overhang. The width for the bottom of the roofline of the towed unit shall be measured separately. Trans 260.09 NoteNote: The outside-to-outside dimension of the unit encompasses protrusions such as windowsills, door knobs and other hardware.
Trans 260.09(4)(4) A permit issued for mobile homes and modular building sections having an outside-to-outside dimension exceeding 15 feet in width, not including roof overhang or having a maximum width for the bottom of the roofline of the towed unit equal to or exceeding 16 feet is subject to the permit conditions applying to 16 foot wide mobile homes and modular building sections in s. Trans 260.16. Trans 260.09(5)(5) Vehicles and loads which when reasonably divided would not be oversize or overweight may not be transported under the permit. Trans 260.09(6)(6) Loads which, when reasonably repositioned on the transporting vehicle, would not be oversize or overweight may not be transported under the permit. Trans 260.09 HistoryHistory: Cr. Register, December, 1990, No. 420, eff. 1-1-91; CR 01-093: am. (3) and (4), r. (5) to (7), renum. (8) and (9) to be (5) and (6), Register June 2002 No. 558, eff. 7-1-02. Trans 260.10(1)(1) Lighting. An oversize vehicle, or a vehicle with an oversize load operating during the hours of darkness, shall be equipped with the following additional lamps: Trans 260.10(1)(a)(a) For a vehicle with a load which extends beyond the width of the vehicle: Trans 260.10(1)(a)1.1. At the outermost extremity of the foremost edge of the projecting load, an amber lamp visible from the front and side. Trans 260.10(1)(a)2.2. At the outermost extremity at the rearmost edge of the projecting load, a red lamp visible from the rear and side. Trans 260.10(1)(a)3.3. Any portion of an overwidth load extending beyond the width of the foremost or rearmost edge of the vehicle or load, shall be marked with an amber lamp visible from the front, both sides, and rear. Trans 260.10(1)(a)4.4. If the overwidth portion of the load measures 3 feet or less from front to rear, that portion shall be marked with an amber lamp visible from the front, both sides and rear, except that if the overwidth projection is located at or near the rear it shall be marked by a red lamp visible from front, side and rear. Trans 260.10(1)(b)(b) For a vehicle with a load which extends more than 4 feet beyond the rear of the vehicle: Trans 260.10(1)(b)1.1. On each side of the projecting load, one red lamp, visible from the side, located so as to indicate maximum overhang. Trans 260.10(1)(b)2.2. On the rear of the projecting load, 2 red lamps, visible from the rear, one at each side; and 2 red reflectors visible from the rear, one at each side, located so as to indicate maximum width. Trans 260.10(1)(c)(c) All required lamps shall be illuminated whenever a vehicle is operated during hours of darkness. All lamps shall be visible at a distance of 500 feet. Trans 260.10(2)(2) Warning lamps. When required by a permit, warning lamps shall be operated as follows: Trans 260.10(2)(a)(a) All mobile homes and modular building sections over 12 feet in width shall have an operating amber flashing or revolving warning lamp a minimum of 8 feet above the roadway at the rear of the towed unit near its center point, visible 500 feet to the rear, or 2 such operating amber flashing or revolving warning lamps, at the left and right rear extremities of the towed unit located a minimum of 8 feet above the roadway and visible 500 feet to the rear. Trans 260.10(2)(b)(b) All amber flashing or revolving warning lamps shall have a reflector at least 6 inches in diameter and shall be bright enough to be clearly visible and attention-attracting at a distance of 500 feet under all conditions when the load is on the highway, except when visibility is obstructed by a hillcrest, a curve, or an object such as another vehicle. Trans 260.10(2)(c)(c) All power units, when transporting a mobile home or modular building section over 81⁄2 feet in width shall have 2 amber flashing or revolving warning lamps mounted above the cab. Flashers shall be mounted at least 8 feet above the roadway and shall be visible to the front. When 2 lamps are provided, they shall be mounted at the same level, shall be separated laterally as much as possible, and shall flash simultaneously. Trans 260.10(2)(d)(d) All warning lamps shall flash at a rate of 30 to 90 times per minute. Trans 260.10(2)(f)(f) Warning lamps may not be operated when a vehicle is not operating under the permit. Trans 260.10(3)(a)(a) When a vehicle, load, or vehicle and load is overlength, a single flag shall be fastened at the extreme rear of the load if the overlength or projecting portion is 2 feet wide or less. Trans 260.10(3)(b)(b) When a vehicle, load, or vehicle and load [is] overlength, 2 flags shall be fastened at the rear of the load to indicate maximum width if the overlength or projecting portion is wider than 2 feet. Trans 260.10(3)(c)(c) When a vehicle, load, or vehicle and load is overwidth, a flag shall be fastened at each front and rear corner of the load. In addition, if any part of the load is more than 4 inches wider than the width of load or vehicle at the front or rear, a flag shall be placed at the widest point of the load. Trans 260.10(3)(d)(d) Each flag shall be solid red or orange in color, and not less than 18 inches square. Trans 260.10(3)(e)(e) In order to wave freely, flags shall be securely fastened by at least one corner or securely mounted on a staff. Trans 260.10(4)(a)(a) When a vehicle, load, or vehicle and load is more than 10 feet in width or is overlength, 2 warning signs shall be displayed. One sign shall be fastened at the front of the power unit and the other at either the rear of the towed unit or at the rear of the load. Trans 260.10(4)(b)(b) Each sign shall state, in black letters on a yellow background,“OVERSIZE LOAD,” and may not be less than 7 feet long and 18 inches high. The letters of the sign may not be less than 10 inches high with a brush stroke of not less than 1.4 inches. Trans 260.10(4)(c)(c) The sign message may not be displayed when the vehicle is not operating under the permit. Trans 260.10(5)(5) Truck weight and tires. Unless otherwise specified in a permit: Trans 260.10(5)(a)(a) A vehicle towing a mobile home or modular building section more than 81⁄2 feet in width but less than 12 feet in width shall be a truck of not less than 16,000 pounds manufacturer’s gross vehicle weight rating. The power unit shall be equipped with dual wheels on the drive axle and the minimum size of the tires shall be 10 ply 8.25 x 20, or equivalent. Trans 260.10(5)(b)(b) A vehicle towing a mobile home or modular building section 12 feet in width, but not more than 16 feet in width, shall be a truck of not less than 19,200 pounds manufacturers’ gross vehicle weight rating. The power unit shall be equipped with dual wheels on the drive axle and the minimum size of the tires shall be 10 ply 8.25 x 20, or equivalent. Trans 260.10(6)(6) Mudguards. Mobile home and modular building sections and the power unit operating under a permit shall be equipped with rear fenders or mudguards of such material and constructed and placed as to restrict to a minimum the splashing of water, mud, stones, and other material which may be thrown up by the rear wheels. If mudguards are provided, they shall be at least as wide as the tire and shall cover the tire or multiple tires they are guarding starting at the top from a line drawn vertically through the center of the axle and extending rearward and downward so that the fender or mudguard under any condition of operation or loading of the vehicle has a ground clearance of not more than 1/3 of the horizontal distance from the center of the rearmost axle to the fender or mudguard. Trans 260.10 HistoryHistory: Cr. Register, December, 1990, No. 420, eff. 1-1-91. Trans 260.11(1)(1) Except as otherwise specified in a permit, no vehicle, or vehicle combination operating under a permit that is equal to or less than 12 feet in width, 131⁄2 feet in height, and 100 feet in length, may operate: Trans 260.11(1)(b)(b) Between 4:00 p.m. and 11:00 p.m. on Friday between the 4th Friday in May and Labor Day. Trans 260.11(1)(c)(c) Between 4:00 p.m. and 11:00 p.m. on any holiday, or, when Independence Day falls on Sunday, on the following Monday. Trans 260.11(1)(d)(d) Between 4:00 p.m. and 11:00 p.m. on the day before any holiday, except that this restriction does not apply to Independence Day when it falls on a Sunday. Trans 260.11(2)(2) In addition to the conditions provided in sub. (1), no vehicle combination operating under a permit that exceeds 12 feet in width, 131⁄2 feet in height, or 100 feet in length, may be operated: Trans 260.11(2)(b)(b) During the period beginning at 12:00 noon on the day preceding and continuing until sunrise on the day following every Sunday and holiday. Trans 260.11(3)(3) In addition to the conditions provided in subs. (1) and (2), no oversize vehicle or vehicle combination may operate on any part of the Milwaukee county expressway system constructed pursuant to s. 59.84, Stats.: Trans 260.11(3)(a)(a) Between 6:00 a.m. and 9:00 a.m. and between 3:00 p.m. and 6:00 p.m. on Monday through Thursday. Trans 260.11(3)(b)(b) Between 6:00 a.m. and 9:00 a.m. and between 3:00 p.m. and 11:00 p.m. on Friday and Sunday. Trans 260.11(3a)(3a) Subsection (3) does not apply to U.S. highway 45 between West Florist Avenue and West Hampton Avenue or to interstate highway 94 between the Waukesha county line and 108th Street. Trans 260.11(4)(4) An issuing authority may issue a permit for times other than those specified in subs. (1), (2), or (3), under extraordinary circumstances when, in the opinion of the issuing authority, public health and welfare is better served, and may impose additional conditions to promote the safe operation of the vehicle and load.
/exec_review/admin_code/trans/260
true
administrativecode
/exec_review/admin_code/trans/260/08/2
Department of Transportation (Trans)
administrativecode/Trans 260.08(2)
administrativecode/Trans 260.08(2)
section
true
