Trans 255.02 HistoryHistory: Cr. Register, December, 1990, No. 420, eff. 1-1-91; CR 13-093: cr. (2) (c) Register July 2014 No. 703, eff. 8-1-14. Trans 255.03(1)(1) An application for a permit shall be submitted to an issuing authority on a form approved by the department, and in accordance with s. 348.27, Stats. Trans 255.03(1m)(1m) The application shall include all requested information, including the applicant’s electronic mail address. Trans 255.03(2)(2) An application for a permit for the use of a state trunk highway shall be made to the department in any of the following ways: Trans 255.03(2)(c)(c) Online through the department’s oversize/overweight automated issuance system. Trans 255.03 NoteNote: Forms used by the department in administering this rule are MV2612 multiple trip permit application and MV 2614 multiple trip permit information. These forms may be obtained in person at or by written request to the DMV Motor Carrier Services Section, Permit Unit, 4802 Sheboygan Avenue, Room 151, P.O. Box 7980, Madison, WI 53707-7980. These forms are also available online at http://www.dot.wisconsin.gov. Forms used by issuing authorities other than the department may be obtained from those authorities. Trans 255.03 NoteNote: Permit application procedures are in s. Trans 250.025. Trans 255.03 HistoryHistory: Cr. Register, December, 1990, No. 420, eff. 1-1-91; correction in (2) (a) made under s. 13.92 (4) (b) 6., Stats., Register February 2013 No. 686; CR 13-093: cr. (1m), am. (2) (a), cr. (2) (c) Register July 2014 No. 703, eff. 8-1-14. Trans 255.04(1)(1) An application for an amendment to a permit shall be made to the issuing authority which issued the original permit. Trans 255.04(2)(2) An application for an amendment may be made in the same manner as an application for an original permit. Trans 255.04(3)(3) The request shall specify the permit number of the permit to be amended. Trans 255.04 NoteNote: Limitations on the amendment of permits are in s. Trans 250.10. Trans 255.04 HistoryHistory: Cr. Register, December, 1990, No. 420, eff. 1-1-91. Trans 255.05(1)(1) Any vehicle or vehicle and load to be considered as operating under a permit shall satisfy requirements for a permit under s. 348.25, Stats. Trans 255.05(2)(2) An issuing authority may not issue a permit for mobile homes or camping trailers under this chapter. Trans 255.05(3)(3) An issuing authority may not issue a permit to transport loads or articles which could reasonably be divided in a manner as to allow transporting of loads or articles in 2 or more loads that are not oversize or overweight, nor may the permit be issued for the transporting of more than one article if the vehicle, load, or vehicle and load is overweight. Trans 255.05 NoteNote: This section prohibits, among other things, addition of an extra boom section to a load that is transported under a permit for an overweight vehicle, load, or vehicle and load. Transporting necessary blocking for a load, or transporting the necessary blocking on an otherwise empty vehicle to and from the origin or destination of the load, is not prohibited.
Trans 255.05(4)(4) An issuing authority may not issue a permit for a vehicle and load exceeding 100 feet in overall length when the rear supporting axle is at or near the rear of the load unless the rear support is separately steered. Trans 255.05(5)(5) An issuing authority may issue a permit only for a vehicle equipped with pneumatic tires. Trans 255.05(6)(6) The issuance of a permit is not a guarantee of the sufficiency of any highway or structure for the transporting of the vehicle, load, or vehicle and load. Trans 255.05(7)(7) A permit may not authorize the operation of more than 2 vehicles in combination except that a vehicle combination consisting of a truck-tractor and semi-trailer, operating under a permit, may transport a 2-axle carry-all scraper with the axle of the scraper power unit resting on the bed of the semi-trailer and the rear axle of the scraper resting on the roadway. The gross weight of the rear axle of the scraper may not exceed 35,000 pounds. Trans 255.05 HistoryHistory: Cr. Register, December, 1990, No. 420, eff. 1-1-91. Trans 255.06(1)(1) A permit is valid only for the vehicle described in the application and permit. Trans 255.06(2)(2) An issuing authority may suspend a permit, or any of its conditions, because of seasonal highway conditions. Trans 255.06(3)(3) No condition of a permit may modify any law or regulation limiting loads because of local conditions, including load limits on bridges and highways, seasonal weight restrictions, or load limits imposed because of construction. Trans 255.06(4)(4) A permit is not valid during periods when adverse weather or road conditions, such as fog, smoke, heavy rain, snow or ice, or wind velocity, impair the safety of a movement under the permit. Trans 255.06(5)(5) Operation under a permit includes the movement of an empty vehicle to and from the place of pickup or delivery of the permitted load. Trans 255.06(6)(6) When a vehicle operating under a permit is overheight, the permittee is responsible for ensuring that the vehicle clear, by at least 3 inches, all overhead structures along the route. If an overheight vehicle hits an overhead structure, the permit becomes invalid immediately at the time the overhead structure is hit. Trans 255.06 NoteNote: Examples of overhead structures are bridges, overpasses, power lines, utility lines and traffic devices.
Trans 255.06 HistoryHistory: Cr. Register, December, 1990, No. 420, eff. 1-1-91; cr. (6), Register, November, 1997, No. 503, eff. 12-1-97. Trans 255.07(1)(1) A vehicle operating under a permit shall be registered as required by Wisconsin Statutes, and shall be registered at not less than the permit weight or at the maximum available registration weight, whichever is less. Trans 255.07(2)(2) All other operational permits required by the department or other agencies having jurisdiction shall be obtained. Trans 255.07 HistoryHistory: Cr. Register, December, 1990, No. 420, eff. 1-1-91; correction in (2) made under s. 13.93 (2m) (b) 6., Stats., Register, August, 1996, No. 488. Trans 255.08(1)(1) The driver of a vehicle operating under a permit shall carry the permit in the vehicle to which it applies and shall have the permit available for inspection by any police officer, representative of the issuing authority, or person in charge of the maintenance of the highway being used. Trans 255.08(2)(2) The driver of a vehicle operating under a permit shall, whenever reasonable and practicable, maintain a distance of not less than 1,000 feet between the permitted vehicle and any vehicle the driver is following, unless actually engaged in overtaking and passing another vehicle. Trans 255.08(3)(3) The driver of a vehicle operating under a permit shall allow traffic approaching or overtaking the permitted vehicle to pass, where it is safe to do so. Trans 255.08(4)(4) The maximum speed of any vehicle with a load 16 feet or wider operating on highways without paved shoulders shall be 35 miles per hour. Trans 255.08(5)(5) Except as provided in sub. (4), or unless a lower speed is specified in the permit, a vehicle operating under a permit may be operated at the posted speed limit. Trans 255.08(6)(6) The right wheels of the towed unit may not leave the roadway, except to allow traffic to pass. Trans 255.08 NoteNote: A “roadway” does not include paved or unpaved shoulders. s. 340.01 (54), Stats. Trans 255.08 HistoryHistory: Cr. Register, December, 1990, No. 420, eff. 1-1-91. Trans 255.09Trans 255.09 Maximum size, weight and loading limitations. Trans 255.09(1)(1) The maximum size, axle, axle combination, and total weight limitations authorized by a permit may not be exceeded. Trans 255.09(2)(2) Property transported under a permit shall be loaded to minimize its size and weight. Trans 255.09(3)(3) An oversize vehicle used for transporting loads under a permit shall be reduced to legal size whenever possible when being operated without load. Trans 255.09 NoteNote: Legal sizes are set forth in ch. 348 and s. 349.16, Stats. Trans 255.09(4)(4) A load transported under a permit may not extend beyond the front of the power unit, beyond the left fender line of the transporting vehicle, or more than 6 inches beyond the right fender of the transporting vehicle, unless the overhang is minimized by suitable positioning of the load upon the vehicle. Trans 255.09(5)(5) Loads consisting of more than one article, none of which are oversize, may not be transported under the permit. Trans 255.09(6)(6) Vehicles and loads which, when reasonably divided, would not be oversize or overweight, may not be transported under the permit. Trans 255.09(7)(7) Loads which, when reasonably repositioned on the transporting vehicle, would not be oversize or overweight, may not be transported under the permit. Trans 255.09(8)(8) Loads consisting of more than one article, one or more of which are oversize, may be transported under a permit only if: Trans 255.09(8)(b)(b) The other articles transported do not cause the vehicle and load to be oversize in any manner differently from the largest single article. Trans 255.09 NoteNote: For example, if a storage tank which is overwidth and overheight (but not overlength) is the single largest article transported, then a toolbox which is not wider, and is not higher, and does not make the vehicle and load overlength or overweight may also be transported.
Trans 255.09 NoteHowever, a beam placed crosswise which makes the overall width wider than the storage tank may not be transported as an additional article. Similarly, a beam placed lengthwise which makes the vehicle and load overlength may not be transported as an additional article.
Trans 255.09 NoteFinally, if the vehicle and load were overweight, then no additional article may be transported.
Trans 255.09(9)(9) The load shall be properly secured and fastened to the transporting vehicle. Trans 255.09(10)(10) Wheels on one side of a transporting vehicle may not carry more than 60% of the total gross load. Trans 255.09 HistoryHistory: Cr. Register, December, 1990, No. 420, eff. 1-1-91. Trans 255.10(1)(1) Lighting. An oversize vehicle, or a vehicle with an oversize load operating during the hours of darkness, shall be equipped with the following additional lamps: Trans 255.10(1)(a)(a) For a vehicle with a load which extends beyond the width of the vehicle: Trans 255.10(1)(a)1.1. At the outermost extremity of the foremost edge of the projecting load, an amber lamp visible from the front and side. Trans 255.10(1)(a)2.2. At the outermost extremity at the rearmost edge of the projecting load, a red lamp visible from the rear and side. Trans 255.10(1)(a)3.3. Any portion of an overwidth load extending beyond the width of the foremost or rearmost edge of the vehicle or load shall be marked with an amber lamp visible from the front, both sides, and rear. Trans 255.10(1)(a)4.4. If the overwidth portion of a load measures 3 feet or less from front to rear, that portion shall be marked with an amber lamp visible from the front, both sides and rear, except that if the overwidth projection is located at or near the rear it shall be marked by a red lamp visible from front, side and rear. Trans 255.10(1)(b)(b) For a vehicle with a load which extends more than 4 feet beyond the rear of the vehicle: Trans 255.10(1)(b)1.1. On each side of the projecting load, one red lamp, visible from the side, located so as to indicate maximum overhang. Trans 255.10(1)(b)2.2. On the rear of the projecting load, 2 red lamps, visible from the rear, one at each side; and 2 red reflectors visible from the rear, one at each side, located so as to indicate maximum width. Trans 255.10(1)(c)(c) All required lamps shall be illuminated whenever a vehicle is operated during hours of darkness. All lamps shall be visible at a distance of 500 feet. Trans 255.10(2)(2) Warning lamps. When required by a permit, warning lamps shall be operated as follows: Trans 255.10(2)(a)(a) All amber flashing or revolving warning lamps shall have a reflector at least 6 inches in diameter and shall be bright enough to be clearly visible and attention-attracting at a distance of 500 feet under all conditions when the load is on the highway, except when visibility is obstructed by a hillcrest, a curve, or an object such as another vehicle. Trans 255.10(2)(b)(b) All warning lamps shall flash at a rate of 30 to 90 times per minute. Trans 255.10(2)(d)(d) Warning lamps may not be operated when a vehicle is not operating under the permit. Trans 255.10(3)(a)(a) When a vehicle, load, or vehicle and load is overlength, a single flag shall be fastened at the extreme rear of the load if the overlength or projecting portion is 2 feet wide or less. Trans 255.10(3)(b)(b) When a vehicle, load, or vehicle and load is overlength, 2 flags shall be fastened at the rear of the load to indicate maximum width if the overlength or projecting portion is wider than 2 feet. Trans 255.10(3)(c)(c) When a vehicle, load, or vehicle and load is overwidth, a flag shall be fastened at each front and rear corner of the load. In addition, if any part of the load is more than 4 inches wider than the width of load or vehicle at the front or rear, then a flag shall be placed at the widest point of the load. Trans 255.10(3)(d)(d) Each flag shall be solid red or orange in color, and not less than 18 inches square.
