NR 538.10(5)(e)(e) Flue gas desulfurization material intended for use as an agricultural soil amendment does not contain contaminant concentrations exceeding the values listed in ch. NR 538 Appendix, Table 3, and will not be applied in volumes exceeding the maximum recommended application rates as determined by the Wisconsin department of agriculture, trade and consumer protection. NR 538.10 NoteNote: USDA Code 333 is the guidance document “Amending Soil Properties with Gypsum Products,” published as Natural Resources Conservation Service Conservation Practices Standard Code 333 (333-CPS-1), June 2015, and is available through the U.S. department of agriculture website: https://www.usda.gov/. NR 538.10 NoteNote: Copies of Wisconsin department of transportation specifications for highway and structure construction and the state highway maintenance manual are available for inspection at the offices of the department of transportation, department of natural resources and the legislative reference bureau.
NR 538.10 NoteNote: Under s. 30.2022, Stats., highway and bridge projects affecting the waters of the state that are carried out under the direction and supervision of the department of transportation are exempt from department permit or approval requirements if accomplished in accordance with interdepartmental liaison procedures established by the department of natural resources and the department of transportation. NR 538.10 HistoryHistory: Cr. Register, December, 1997, No. 504, eff. 1-1-98; CR 05-020: am. (5) (a) to (d), (f), (7) (b), (8) to (10), renum. (11) and (12) to be (12) and (13) and am., cr. (5) (h), (i) and (11) Register January 2006 No. 601, eff. 2-1-06; CR 19-080: r. and recr. Register May 2020 No. 773, eff. 11-1-20; correction in (3) (b) made under s. 13.92 (4) (b) 7., Stats., and correction in (2) (b), (f) 5., (5) (intro.) made under s. 35.17, Stats., Register May 2020 No. 773. NR 538.12NR 538.12 Additional criteria for the beneficial use of industrial byproducts as geotechnical fill. NR 538.12(1)(1) All geotechnical fill uses shall comply with the performance standards under s. NR 538.04 and the applicable criteria in this section. NR 538.12(2)(2) Industrial byproducts that are utilized for any of the uses under s. NR 538.10 (2) shall be placed in accordance with all of the following: NR 538.12(2)(a)(a) Industrial byproducts may not be placed within areas of permanent standing water or areas that need to be dewatered prior to placement due to groundwater infiltration. NR 538.12(2)(b)(b) For those beneficial uses listed in s. NR 538.10 (2) that use industrial byproducts designated by the department as select foundry sand under s. NR 538.06 (3) (f) or that do not exceed the concentrations specified in ch. NR 538 Appendix, Table 1, Column A, there shall be a minimum separation distance of 3 feet between the industrial byproduct and the groundwater table at the time of placement, except geotechnical fill used for nonmetallic mine reclamation projects under s. NR 538.10 (2) (f), which shall maintain a minimum separation distance as determined by s. NR 538.10 (2) (f) 5. NR 538.12(2)(c)(c) For those beneficial uses listed in s. NR 538.10 (2) that use industrial byproducts, excluding select foundry sand, that exceed the concentrations specified in ch. NR 538 Appendix, Table 1, Column A, but are less than the concentrations specified in ch. NR 538 Appendix, Table 1, Column B, there shall be a minimum separation distance of 5 feet between the industrial byproducts and the groundwater table at the time the material is placed. NR 538.12(2)(d)(d) Industrial byproducts may not be placed within an area that meets the definition of a floodplain under s. NR 116.03 (16) or below the ordinary high-water mark within any navigable waters as defined under s. NR 115.03 (6) without prior written approval from the department. NR 538.12(2)(e)(e) Industrial byproducts used as geotechnical fill as part of the reclamation of nonmetallic mine sites in accordance with s. NR 538.10 (2) (f) may not exceed the concentrations in s. NR 538 Appendix, Table 1, Column A unless designated by the department as select foundry sand under s. NR 538.06 (3) (f). NR 538.12(3)(3) Industrial byproducts that are used for the beneficial uses listed in s. NR 538.10 (2) and exceed 5,000 cubic yards may not be placed closer than 100 feet from a private or public water well. Prior written notification to the department in accordance with s. NR 538.14 (5) and concurrence by the department under s. NR 538.14 (6) is required for separation distances less than 100 feet. Concurrence by the department shall be based on site-specific conditions such as well construction and ground water flow direction. NR 538.12(4)(4) Beneficial use projects utilizing fill materials under s. NR 538.10 (2) shall be completed, including the placement of final cover, within 12 months of first accepting industrial byproduct material. This period may be extended to no more than 16 months provided the site is adequately secured from public access by means of exclusion fencing and signage or other equally effective means as approved by the department in writing. If the beneficial use project requires more than 12 months to complete, or 16 months to complete if the site is adequately secured, the project shall be planned in phases with each phase of filling completed and interim or final cover placed prior to initiation of filling the next phase. Prior to use of an alternate cover, the generator, or the generator’s designee, shall provide a written request to the department. A written approval by the department may be granted based upon site-specific conditions and good engineering practices. NR 538.12(5)(5) Confining surfaces and soil cover in beneficial use projects utilizing fill materials under s. NR 538.10 (2) shall be maintained as designed. Fill materials exposed by erosion, excavation, or weathering shall be covered in accordance with the original design, or as approved by the department, as soon as practical. Requests for modification of the final cover shall be made in accordance with s. NR 538.14 (7), and excavation of fill material shall be performed in accordance with s. NR 538.24. NR 538.12(6)(6) Beneficial use projects proposing utilization of 100,000 cubic yards or more of geotechnical fill materials under s. NR 538.10 (2) shall require a request to the department by the generator, or the generator’s designee, for a case-specific approval in accordance with s. NR 538.09. NR 538.12(7)(7) All vegetated soil covers over geotechnical fill materials under s. NR 538.10 (2) shall utilize topsoil in sufficient quantities and of sufficient quality to support a vegetative cover that prevents erosion. NR 538.12(8)(8) All geotechnical fill projects under s. NR 538.10 (2) shall be conducted in a manner to minimize windblown dust, odor, tracking, and spillage of the industrial byproduct and not to cause nuisance conditions. NR 538.12 HistoryHistory: Cr. Register, December, 1997, No. 504, eff. 1-1-98; CR 05-020: am. (2) (b), r. (2) (d), cr. (2) (br) Register January 2006 No. 601, eff. 2-1-06; correction in (3), (4) and (5) made under s. 13.93 (2m) (b) 7., Stats., Register May 2006 No. 605; correction in (1) made under s. 13.92 (4) (b) 7., Stats., Register February 2010 No. 650; CR 19-080; r and recr. Register May 2020 No. 773, eff. 11-1-20; correction in (2) (b), (e), (3), (5) made under s. 35.17, Stats., Register May 2020 No. 773. NR 538.14(1)(1) Initial certification. Prior to beneficial use of industrial byproducts under this chapter, or the establishment of a non-exempt storage facility, each generator, non-exempt storage facility operator, or the generator’s designee, shall submit an initial certification form to the department. An initial certification form shall be submitted prior to beneficial use in accordance with this chapter for any industrial byproduct not previously approved for eligible uses, for any industrial byproduct for which the generation process has changed, or for the establishment of a storage facility for industrial byproducts. The initial certification form shall include all of the following information: NR 538.14(1)(a)(a) The name and address of the generator or storage facility operator. NR 538.14(1)(b)(b) The name, address, and telephone number of the designated generator or storage facility operator contact. NR 538.14(1)(c)(c) A description of each industrial byproduct intended for beneficial use or storage that clearly identifies the process that generated the material and an estimate of the volume that may be made available for beneficial use on an annual basis. NR 538.14(1)(d)(d) Initial byproduct characterization results as required under s. NR 538.06 (1) to (3), including a listing of the eligible uses of each industrial byproduct to be beneficially used or stored for beneficial use in accordance with s. NR 538.10 and ch. NR 538 Appendix, Tables 1 to 3. Documentation, including test results supporting the eligible use determinations, shall be included. Non-exempt storage facilities under s. NR 538.16 (1) (a) shall provide the name and address of the generators of the industrial byproducts to be stored unless the storage facility is located at the same address as the industrial byproduct generating facility. NR 538.14(1)(e)(e) Authorization for Wisconsin department of natural resources staff to conduct inspections of the facilities generating industrial byproducts being beneficially used under this chapter or storage facilities for those industrial byproducts and collect samples to verify compliance with this chapter. NR 538.14(1)(f)(f) Certification by each generator, or the generator’s designee, and each storage facility operator, or the operator’s designee, that the information on the form is true and accurate, and that the performance standards of s. NR 538.04 will be met. NR 538.14 NoteNote: Copies of the initial certification form may be obtained from the department of natural resources, bureau of waste management, 101 South Webster Street, Natural Resources Building, P.O. Box 7921, Madison, Wisconsin 53707-7921.
NR 538.14(2)(2) Recharacterization. Each generator of industrial byproducts that have been beneficially used under this chapter, operator of a non-exempt storage facility for industrial byproducts as required under s. NR 538.16 (1) (a), or the designee of the generator or operator, shall submit recertification information used to determine the eligible use of each industrial byproduct, electronically or on a form supplied by the department, every 4 years or after a process change in accordance with s. NR 538.06 (5). The recertification form shall be submitted to the department no later than 60 days following the receipt of the analytical testing results which indicate a potential reassignment of the eligible uses for any industrial byproduct. Analytical testing results that confirm the eligible uses assigned during the initial certification or the previous recharacterization may be submitted with the annual certification under sub. (3). The recertification form shall include all of the following information: NR 538.14(2)(a)(a) The name and address of the generator or storage facility operator. NR 538.14(2)(b)(b) The name, address, and telephone number of the designated generator or storage facility operator contact. NR 538.14(2)(c)(c) A description of each industrial byproduct intended for beneficial use or storage that clearly identifies the process and location of the generating facility. NR 538.14(2)(d)(d) Documentation, including analytical testing results, supporting the eligible use classifications as specified under s. NR 538.08. NR 538.14(2)(e)(e) Certification by the generator, or the generator’s designee, or the storage facility operator, or the operator’s designee, that the information on the form is true and accurate. NR 538.14(3)(3) Annual certification. Each generator of industrial byproducts that have been beneficially used under this chapter, operator of a non-exempt storage facility for industrial byproducts as required under s. NR 538.16 (1) (a), or the generator’s or operator’s designee, shall submit an annual certification, electronically or on a form supplied by the department, that documents the amount of material beneficially used for each eligible use in the previous calendar year and confirms the proper use of each industrial byproduct. The certification form shall be submitted no later than April 1 of the year following the reporting period. The annual certification form shall include all of the following information: NR 538.14(3)(a)(a) The name and address of the generator or storage facility operator. NR 538.14(3)(b)(b) The name, address, and telephone number of the designated generator or storage facility operator contact. NR 538.14(3)(c)(c) A description of each industrial byproduct intended for beneficial use or storage that clearly identifies the process and location of the generating facility. NR 538.14(3)(d)(d) The volume of each industrial byproduct that was beneficially used during the reporting period, identified by types of beneficial uses under s. NR 538.10. If the industrial byproduct was given or sold to an entity other than the generator for subsequent use or distribution, the name and address of the recipient shall be listed along with the volume the recipient received and the intended beneficial uses. NR 538.14(3)(e)(e) For non-exempt storage facilities, the volume of each industrial byproduct that was in storage as of December 31 of the reporting year. NR 538.14(3)(f)(f) Documentation, including test results, supporting any required recharacterization as specified in s. NR 538.06 (5). A non-exempt storage facility under s. NR 538.16 (1) (a) shall provide the name and address of the generators of the industrial byproducts to be stored unless the storage facility is located at the industrial byproduct generating facility. NR 538.14(3)(h)(h) Certification by the generator, or the generator’s designee, or storage facility operator, or the operator’s designee, that the information on the form is true and accurate, and that the performance standards of s. NR 538.04 have been met. NR 538.14 NoteNote: Copies of the annual certification form may be obtained from the department of natural resources, bureau of waste management, 101 South Webster Street, Natural Resources Building, P.O. Box 7921, Madison, Wisconsin 53707-7921.
NR 538.14(4)(4) Exemption. Subsection (2) does not apply if the volume of the generator’s industrial byproducts beneficially used, or stored for future use, during the reporting period was less than 1,000 cubic yards. NR 538.14(5)(5) Notification. Each generator, or a person designated by the generator such as a broker, shall submit written notification to the department prior to initiating a project when required under ss. NR 538.10 (2) and NR 538.12. All of the following information shall be included in the notification: NR 538.14(5)(a)(a) The name, address, and phone number of the contact for the project. NR 538.14(5)(b)(b) The location of the project and a site description, including a topographic or orthophoto map, township and range to the quarter section, and land use information. In addition, the applicant shall submit geographic information system locational information based on no fewer than 6 geographically informative points that define the limits of industrial byproduct placement. These points shall be collected using the North American Datum, NAD83 (1991). For each point, the longitude and latitude shall be referenced to the 5th decimal degree. The date, method, and tools used to collect locational information for each point shall also be included. Other methods of geolocation that provide similar or better accuracy are also acceptable, subject to approval by the department. NR 538.14(5)(c)(c) The approximate volume of industrial byproduct anticipated to be used in the project. NR 538.14(5)(d)(d) The anticipated start and end dates for the project and the timing of any phasing. NR 538.14(5)(e)(e) Identification of the types and generators of the industrial byproducts to be used and the eligible uses of these materials. NR 538.14(5)(f)(f) Information demonstrating that the proposed project will meet the performance standards and beneficial use specifications of this chapter. NR 538.14(5)(g)(g) For those beneficial uses listed in s. NR 538.10 (2) that exceed 5,000 cubic yards, the method and the data used to determine the groundwater separation distance. NR 538.14(5)(i)(i) For those beneficial uses subject to the public notification requirement under s. NR 538.18, proof that a public notice was placed in the local newspaper in accordance with s. NR 538.18 (1) (a). NR 538.14 NoteNote: Proof of a public notice may include a copy of the notice clipped from the newspaper along with the date it was published or any other notification verifying that an order for the public notice was placed with the newspaper and the expected date of publication.
NR 538.14(6)(6) Concurrence. For proposed projects that require submission of a written notification, the department shall reply with a written concurrence within 10 business days provided the applicant meets the applicable criteria of this chapter. If the department determines that the proposal does not demonstrate that the project will meet the applicable criteria, the department shall provide a written notice of non-concurrence within 10 business days, noting any deficiencies and allowing the applicant an opportunity to correct them or provide additional information. If the department does not respond to the notification within 10 business days, concurrence is considered granted. NR 538.14(7)(7) Modifications. Any generator, or the generator’s designee, that wishes to modify a project for which the department granted concurrence under sub. (6) shall notify the department in writing describing the nature of the modification requested. In determining if a modification is required, the applicant shall consider if the proposed modification alters the original project footprint, substantially increases the volume of the byproduct material, or has the potential to affect any of the performance standards under s. NR 538.04. The department shall review the modification request and notify the applicant in writing if submission of a revised notification under sub. (5) is required. If the department does not respond to the notification within 10 business days, the modification is deemed complete and concurrence is considered granted. NR 538.14(8)(8) Record keeping. The generator, or the generator’s designee, shall maintain records of where industrial byproducts have been utilized under this chapter for one or more of the beneficial uses described under s. NR 538.10 (2). These records shall be maintained and be accessible to department staff upon request for 5 years after the use of the industrial byproduct. NR 538.14 HistoryHistory: Cr. Register, December, 1997, No. 504, eff. 1-1-98; CR 05-020: am. (4) (intro.), cr. (4) (f) Register January 2006 No. 601, eff. 2-1-06; CR 19-080: r. and recr. Register May 2020 No. 773, eff. 11-1-20; correction in (2) (intro.), (4), (5) (g) made under s. 35.17, Stats., Register May 2020 No. 773; correction in (1) (d), (2) (intro.), (d), (3) (intro.) made under s. 13.92 (4) (b) 7., Stats., Register February 2021 No. 782; correction in (3) (f), (g) made under s. 13.92 (4) (b) 7., Stats., Register August 2022 No. 800. NR 538.16NR 538.16 Storage and transportation requirements. NR 538.16(1)(a)(a) Storage of industrial byproducts for beneficial use shall meet the performance standards specified in s. NR 538.04. Storage facilities shall also satisfy all of the following: NR 538.16(1)(a)1.1. The storage facility shall meet all of the following design and operational criteria: NR 538.16(1)(a)1.a.a. Areas intended for the storage of industrial byproducts that have been determined to contain greater than the concentrations specified for the parameters listed in ch. NR 538 Appendix, Table 1, Column B shall incorporate an impervious surface pad and be surrounded by curbs or berms to control surface water run-on and run-off. Alternately, if a low permeability clay surface is used, it shall include a protective material cover of, at a minimum, one foot of gravel or an equivalent material over the clay. Areas intended for the storage of byproducts that have been determined to contain less than the concentrations specified for the parameters listed in ch. NR 538 Appendix, Table 1, Column B shall construct a surface pad beneath the storage pile consisting of either an impervious surface, compacted soil, or an aggregate surface with a minimum one-foot thickness or an equally effective design as approved by the department in writing. NR 538.16(1)(a)1.b.b. Storage facilities shall be operated and maintained to minimize dust, off-site tracking, and storm water runoff. The storage area shall be clearly delineated and lined on 3 sides with curbs, blocks or berms designed to prevent spillage and contain the byproduct to the designated storage area. A setback shall be maintained between the stored material and the entrance to the storage area to prevent spillage of material and to reduce off-site tracking. NR 538.16(1)(a)2.2. The operator of the storage facility shall provide the department an annual certification in accordance with s. NR 538.14, including a summary of the storage facility performance, problems, and maintenance in the annual certification under s. NR 538.14 (3) (g) and an affirmation that the impervious or low permeability surface pad, if required, still meets the design criteria specified in subd. 1. a. NR 538.16(1)(a)3.3. Upon closure of an industrial byproduct storage facility, the storage operator shall remove all visible residues from the storage area. NR 538.16(1)(b)(b) All of the following industrial byproduct storage facilities are exempt from the requirements of this subsection: NR 538.16(1)(b)1.1. Facilities for the storage of industrial byproducts contained within enclosed structures such as buildings, silos, or roll-off boxes. NR 538.16(1)(b)2.2. Facilities for the storage of industrial byproducts within a lined area at a licensed engineered landfill. Storage of industrial byproducts at a licensed engineered landfill shall be subject to the conditions of the plan of operation and any other applicable solid waste approvals associated with the landfill. NR 538.16(1)(b)3.3. Municipal maintenance and storage facilities that stockpile no more than 300 cubic yards of industrial byproduct material at any given time. The stored material shall be contained by perimeter berms or curbs. These facilities shall be operated and maintained to minimize dust, minimize off-site tracking, and manage storm water runoff. NR 538.16(1)(b)4.4. Facilities for the temporary off-site storage or staging of industrial byproducts to be used beneficially in accordance with s. NR 538.10. These temporary facilities shall be operated and maintained to minimize dust, off-site tracking, and storm water runoff, and limit public access. Industrial byproducts may not remain in temporary off-site storage or staging areas for more than 16 months after the date of their placement. These facilities shall provide to the department written notice of the storage location, the date on which the storage of materials began, and the total volume stored. NR 538.16(1)(b)5.5. Facilities for which the department issues an exemption on a case-specific basis in accordance with s. NR 538.09. NR 538.16 NoteNote: The discharge of stormwater is regulated under ch. NR 216. NR 538.16(2)(2) Transportation. A vehicle or container used to transport industrial byproducts intended for beneficial use shall meet all of the following criteria: NR 538.16(2)(a)(a) The vehicle or container shall be designed and built to be durable and leak-proof and maintained to prevent nuisance conditions from occurring. NR 538.16(2)(b)(b) The vehicle or container shall be loaded and hauled in such a manner that the contents do not fall, spill, or leak, including the use of covers as necessary. Any spilled industrial byproduct shall be properly recovered. NR 538.16 NoteNote: Storage and transportation of industrial byproduct in accordance with this chapter are exempt from the storage and transportation requirements of ch. NR 502 as specified in ss. NR 502.05 (3) (i) and 502.06 (2) (k). NR 538.16 HistoryHistory: Cr. Register, December, 1997, No. 504, eff. 1-1-98; CR 05-020: am. (1) (a) 4. Register January 2006 No. 601, eff. 2-1-06; CR 19-080: r. and recr. Register May 2020 No. 773, eff. 6-1-20. NR 538.18(1)(1) Notification. Except as provided in sub. (2), no person may initiate a beneficial use project where the volume of the industrial byproduct to be used is greater than 30,000 cubic yards, or construct or operate a permanent or temporary storage facility with a design capacity greater than 30,000 cubic yards, prior to the person giving notice to the affected public and providing for adequate public participation. Unless other forms of public notification and involvement are approved by the department in writing, the notice and public participation process provided by the person intending to initiate a beneficial use project or storage facility shall include, at a minimum, all of the following: NR 538.18(1)(a)(a) Placing a public notice in the local newspaper at least 30 business days prior to initiating an industrial byproduct beneficial use project or storage facility, specifying the nature of the beneficial use project or storage facility, including the type and amount of the material to be used or stored, how and where the material will be used, the time frame of the project or storage facility operation, that the person intending to initiate the beneficial use project or storage facility may hold a public informational meeting either electively or if requested, and a contact person for the public to request a meeting. NR 538.18 NoteNote: The public informational meeting is not considered an informational hearing under s. 289.26, Stats., even if department staff elect to participate. NR 538.18(1)(b)(b) Holding a public informational meeting, if requested by the public, at which details of the project can be discussed. Department staff may participate in the meeting. NR 538.18(2)(a)(a) The following beneficial use projects are exempt from the public participation requirements under this section: