NR 422.084(10)(a)(a) Compliance schedule. The owner or operator of a facility with plastic parts coating operations shall comply with the applicable requirements of this section upon the facility becoming subject to this section as provided under sub. (1), except for any of the following: NR 422.084(10)(a)1.1. The owner or operator of a facility with plastic parts coating operations subject to this section that commenced construction before June 1, 2022, shall comply with applicable requirements of this section by November 28, 2022. Any facility that was subject to s. NR 422.083 before June 1, 2022, shall continue to comply with the requirements in s. NR 422.083 until the date when the facility is in compliance with the applicable requirements of this section or until November 28, 2022, whichever is sooner. NR 422.084(10)(a)2.2. The owner or operator of a facility with plastic parts coating operations that becomes subject to this section due to either the designation or the reclassification of a nonattainment area that occurs after June 1, 2022, shall comply with applicable requirements of this section 180 days after the effective date of the nonattainment designation or reclassification, as indicated by the relevant Federal Register publication. NR 422.084(10)(b)(b) Certification. No later than 60 days after the compliance deadline specified under par. (a), the owner or operator of a facility with plastic parts coating operations subject to this section shall submit to the department written certification that all affected plastic parts coating operations are in compliance with the applicable requirements of this section. The owner or operator of a facility subject to s. NR 422.083 before June 1, 2022, that is required to have an operation permit under ch. NR 407 shall submit to the department a permit application or a permit revision or renewal application that meets the requirements of s. NR 407.05 to meet this certification requirement, except that no application shall be required for a source operating under a general operation permit or a registration operation permit issued under s. NR 407.10 or 407.105. NR 422.084 HistoryHistory: CR 20-088: cr. Register May 2022 No. 797, eff. 6-1-22; correction in (10) (a) 1. made under s. 13.92 (4) (b) 14., Stats., Register May 2022 No. 797. NR 422.085(1)(1) Applicability. Effective February 1, 1987, this section applies to coating applications at leather coating facilities which are either of the following: NR 422.085(1)(a)(a) Located in the county of Kenosha, Milwaukee, Ozaukee, Racine, Washington, or Waukesha, and which have maximum theoretical emissions of VOC from the facility greater than or equal to 25 tons per year. NR 422.085(1)(b)(b) Located in the county of Door, Kewaunee, Manitowoc, Sheboygan, or Walworth, and which have maximum theoretical emissions of VOC from the facility greater than or equal to 100 tons per year. NR 422.085(2)(2) Emission limitations. No owner or operator of a leather coating facility may cause, allow or permit the emission of any VOCs from coating applications in excess of 18.6 kilograms per 100 square meters (38.0 pounds per 1000 square feet) of coated product calculated on a daily average basis. NR 422.085(3)(3) Compliance requirements and schedules. The owner or operator of a leather coating facility shall comply with the requirements of sub. (4) and s. NR 425.03 (1), (8), and (9). NR 422.085(4)(a)(a) To determine compliance with the leather coating VOC emission limit in this section, the facility shall maintain daily coating usage and leather production records in a format approved by the department. Reporting, recordkeeping and access to these records shall be in accordance with ss. NR 439.03 to 439.05. NR 422.085(4)(b)(b) The daily VOC emission rate shall be determined by the following equation: where:
c is the daily average VOC emission rate
a is the total amount of VOCs emitted during the day
b is the prorated surface area of leather coated during the day, where:
di is the total area of the ith batch of hides coated during the day
ei is the ratio of actual VOC emissions resulting from coating any portion of the ith batch of hides during the day to the total predicted VOC emissions resulting from all coating of the entire ith batch
NR 422.085(4)(c)(c) The facility shall measure the surface area of each piece of leather coated with a mechanism initially calibrated for minimum accuracy to the Turner Korrect Machine or Sawyer Measurement systems. The average surface area per coated piece of leather may be used for a batch of leather provided that the average is based on a minimum of 500 pieces. Otherwise, the facility average surface area per coated leather piece shall be used. In no case may the total area allocated to production over all days from a piece of leather exceed the average area for that leather. NR 422.085 HistoryHistory: Cr. Register, January, 1987, No. 373, eff. 2-1-87; am. (2) and (3), cr. (4), Register, February, 1990, No. 410, eff. 3-1-90; CR 11-005: renum. (1) to be (1) (intro.) and am., cr. (1) (a), (b) Register January 2012 No. 673, eff. 2-1-12. NR 422.09NR 422.09 Automobile and light-duty truck manufacturing. NR 422.09(1)(a)(a) This section applies to the application areas, flashoff areas, and ovens of automobile and light-duty truck manufacturing plants involved in prime, topcoat, and final repair coating of metallic front end and main body parts at any facility located in the county of Kenosha, Milwaukee, Ozaukee, Racine, Sheboygan, Washington, or Waukesha if VOC emissions from the prime, topcoat, and final repair coating and related cleaning activities at the facility, before consideration of controls, equal or exceed 3 tons per year on a 12 consecutive month rolling basis. NR 422.09(1)(b)(b) Subsections (2) to (5) apply to the coating operations described in par. (a) at any automobile and light-duty truck manufacturing facility located in the county of Brown, Calumet, Dane, Dodge, Door, Fond du Lac, Jefferson, Kewaunee, Manitowoc, Outagamie, Rock, Walworth, and Winnebago if VOC emissions from all coating operations described in par. (a) at the facility, before consideration of controls, equal or exceed 6.8 kilograms (15 pounds) in any one day. NR 422.09(1)(c)(c) Subsections (2) to (5) apply to coating operations as described in par. (a) at any automobile and light-duty truck manufacturing facility not subject to par. (a) or (b) if total VOC emissions from the facility, before consideration of controls, equal or exceed 100 tpy. NR 422.09(1)(d)(d) Subsections (2) to (5) do not apply to the coating of wheels, trunk interiors, steering columns, or nonmetallic parts; sealers; nonpriming anti-rust coatings; or processes, coatings, or inks described in s. NR 422.03 (5) and (7). NR 422.09(2)(2) Emission limitations—enamels. No owner or operator of an automobile surface coating line which, prior to January 1, 1979, used an enamel coating system, may cause, allow or permit the emission of any VOCs in excess of: NR 422.09(2)(a)(a) After December 31, 1983, 0.14 kilograms per liter of coating (1.2 pounds per gallon), excluding water, from an electrodeposition prime coat or equivalent coating line. NR 422.09(2)(b)(b) After December 31, 1982, 0.34 kilograms per liter of coating (2.8 pounds per gallon), excluding water, from a spray primer-surfacer coating line. NR 422.09(2)(d)(d) After December 31, 1985, 0.34 kilograms per liter of coating (2.8 pounds per gallon), excluding water, from a topcoat coating line. NR 422.09(2)(e)(e) After December 31, 1982, 0.58 kilograms per liter of coating (4.8 pounds per gallon), excluding water, from any final repair coating line. NR 422.09(3)(3) Emission limitations—lacquers. No owner or operator of an automobile surface coating line which, prior to January 1, 1979, used a lacquer coating system, may cause, allow or permit the emission of any VOCs in excess of: NR 422.09(3)(b)(b) After December 31, 1982, 0.14 kilograms per liter of coating (1.2 pounds per gallon), excluding water, from an electrodeposition prime coat coating line. NR 422.09(3)(d)(d) After December 31, 1986, 0.34 kilograms per liter of coating (2.8 pounds per gallon), excluding water, from a spray primer-surfacer coating line. NR 422.09(3)(g)(g) After December 31, 1986, 0.34 kilograms per liter of coating (2.8 pounds per gallon), excluding water, from a topcoat coating line. NR 422.09(3)(i)(i) After December 31, 1986, 0.58 kilograms per liter of coating (4.8 pounds per gallon), excluding water, from any final repair coating line. NR 422.09(4)(4) Emission limitations—trucks. No owner or operator of a light-duty truck surface coating line may cause, allow or permit the emission of any VOCs in excess of: NR 422.09(4)(b)(b) After December 31, 1982, 0.14 kilograms per liter of coating (1.2 pounds per gallon), excluding water, from an electrodeposition prime coat coating line. NR 422.09(4)(d)(d) After December 31, 1987, 0.34 kilograms per liter of coating (2.8 pounds per gallon), excluding water, from a spray primer-surfacer coating line. NR 422.09(4)(f)(f) After December 31, 1987, 0.34 kilograms per liter of coating (2.8 pounds per gallon), excluding water, from a topcoat coating line. NR 422.09(4)(g)(g) After December 31, 1982, 0.58 kilograms per liter of coating (4.8 pounds per gallon), excluding water, from any final repair coating line. NR 422.09(5)(5) Emission rate averaging. Each emission limit in this section may be interpreted as a weighted daily average, if specified in an approved compliance plan. The emission limits are referenced to waterborne coatings conventionally applied. Any coating line which achieves an equivalent emission rate per unit area coated shall be deemed in compliance. NR 422.09(6)(6) Work practices. Beginning on March 1, 2013, the owner or operator of a facility subject to this section shall do all of the following: NR 422.09(6)(a)(a) Minimize VOC emissions from cleaning of storage, mixing and conveying equipment. NR 422.09(6)(b)(b) Develop and implement a work practice plan to minimize VOC emissions from cleaning and purging of equipment associated with all coating operations. The plan shall specify practices and procedures for the following operations, at a minimum: NR 422.09 HistoryHistory: Renum. from NR 154.13 (4) (g) and am. Register, September, 1986, No. 369, eff. 10-1-86; am. (2) (intro.), (3) (intro.), (4) (intro.) and (5), Register, February, 1990, No. 410, eff. 3-1-90; r. (2) (c), (3) (a), (c), (e), (f) and (h), (4) (a), (c) and (e), Register, December, 1995, No. 480, eff. 1-1-96; CR 11-005: renum. (1) to be (1) (a) and am., cr. (1) (b) to (d), (6) Register January 2012 No. 673, eff. 2-1-12. NR 422.095NR 422.095 Automobile refinishing operations. NR 422.095(1)(a)(a) Subsections (3) to (5) apply to automobile refinishing operations performed in the following types of facilities in the counties of Kenosha, Kewaunee, Manitowoc, Milwaukee, Ozaukee, Racine, Sheboygan, Washington, and Waukesha: auto body and repair shops; production paint shops; new and used motor vehicle dealer repair and paint shops; fleet operator repair and paint shops; and any facility which coats vehicles and is classified under standard industrial classification code 7532, as described in the Standard Industrial Classification Manual, 1987, incorporated by reference in s. NR 484.05 (1), including dock repair of imported vehicles and dealer repair of vehicles damaged in transit. NR 422.095(1)(b)(b) Subsections (7) and (8) apply to the owner or operator of a facility specified in par. (a) which is located in the county of Kenosha, Milwaukee, Ozaukee, Racine, Sheboygan, Washington, or Waukesha if VOC emissions from all industrial cleaning operations associated with automobile refinishing operations at the facility, before consideration of controls, equal or exceed 3 tons on a 12 consecutive month rolling basis. NR 422.095(2)(a)(a) Automobile refinishing operations at facilities which use less than 20 gallons per year of coatings are exempt from the equipment requirements in sub. (5). NR 422.095(2)(b)(b) The application of touch-up coatings is exempt from this section. NR 422.095(2)(c)(c) Subsection (7) does not apply to the stripping of cured coatings or cured inks. NR 422.095(2)(e)(e) Subsection (7) (a) does not apply to cleaning conducted in conjunction with performance laboratory tests on coatings or inks; research and development programs; and laboratory tests in quality assurance laboratories. NR 422.095(2)(f)(f) Subsection (7) (a) and (e) do not apply to cleaning with aerosol products if 160 fluid ounces or less of VOC-containing aerosol products are used per day for industrial cleaning operations per facility. NR 422.095(2)(i)(i) Subsection (7) (e) does not apply to the cleaning of the nozzle tips of automated spray equipment systems, except for robotic systems that are programmed to spray into a closed container. NR 422.095(3)(a)(a) The owner or operator of an automobile refinishing operation in existence on September 1, 1995, and subject to this section, shall submit a notification to the department, in writing, within 60 days of September 1, 1995, consisting of the following information: NR 422.095(3)(a)1.1. Name, address and phone number of facility where refinishing operations are taking place. NR 422.095(3)(b)(b) The owner or operator of an automobile refinishing operation which becomes subject to this section shall submit a written notification to the department containing the information specified in par. (a) within 30 days after becoming subject to this section. NR 422.095 NoteNote: Notifications submitted under this subsection should be submitted to:
NR 422.095 NoteWisconsin Department of Natural Resources
Bureau of Air Management
PO Box 7921
Madison WI 53707-7921
Attn: Small Business Section
NR 422.095(4)(a)(a) No owner or operator of an automobile refinishing operation may refinish or allow the refinishing of any motor vehicles or their body parts and components using any coating or coating system with a VOC content in excess of that specified in Table 2. All coatings and coating components shall be used according to manufacturer’s specifications and mixing instructions. NR 422.095(4)(b)(b) The most restrictive VOC limitation in Table 2 applies with either of the following: NR 422.095(4)(b)1.1. Different combinations or mixing ratios of coatings and coating components are used which constitute a different coating system than any of the systems listed in Table 2. NR 422.095(4)(b)2.2. The same combination and mixing ratio of coating components is used for more than one category in Table 2. NR 422.095(4)(c)(c) Automobile refinishing coatings and coating components manufactured prior to January 11, 1999 are exempt from the emission limitations in Table 2. NR 422.095(4)(d)(d) The maximum VOC content for any category of coating in Table 2 shall be calculated according to the following formula: where:
VOC content is the pounds of VOC per gallon of coating
/exec_review/admin_code/nr/400/422
true
administrativecode
/exec_review/admin_code/nr/400/422/09/1/c
Department of Natural Resources (NR)
Chs. NR 400-499; Environmental Protection – Air Pollution Control
administrativecode/NR 422.09(1)(c)
administrativecode/NR 422.09(1)(c)
section
true
