SECTION 17. NR 422.143 (6) (intro.) and (a) are amended to read:
NR 422.143 (6) RECORDKEEPING REQUIREMENTS. In addition to the applicable recordkeeping requirements in s. NR 439.04, the owner or operator of any lithographic printing press shall collect and record the applicable information specified in this subsection. The information shall be maintained at the facility for a minimum of 5 years and shall be made available to an authorized department representative at any time during normal working hours. The information required is all of the following: (a) For a heatset web lithographic printing press using a control device, for each day of operation all of the following:
1. Control device Temperature monitoring data for the control device in accordance with s. NR 439.055 sub. (5) (b) 1. for each day of operation. 2. A log of the operating time for or record of any time when the control device, or control device monitoring equipment, and is offline while the associated printing line or is in operation.
3. A maintenance log for the control device and control device monitoring equipment detailing all routine and non−routine maintenance performed and including the dates and duration of any outages.
SECTION 18. NR 422.143 (6) (a) 4. is created to read:
NR 422.143 (6) (a) 4. Annual inspection results for catalytic oxidizers.
SECTION 19. NR 422.143 (6) (d) and (e) and (7) (a) and (b) 1. and 2. are amended to read:
NR 422.143 (6) (d) For each batch of blanket or roller wash cleaning solution prepared, the percent by weight VOC content or the VOC composite partial vapor pressure, and the date and time the batch was for the cleaning solution prepared.
(e) For each month of operation, the volume of all blanket or roller wash cleaning solutions used which does that do not meet either of the emission limitations in sub. (3) (c).
(7) (a) The owner or operator of a heat-set web lithographic printing press shall demonstrate compliance with the appropriate destruction efficiency or emission rate in sub. (3) (a) by performing compliance emission tests on each control device. The initial emission tests shall be performed by the compliance deadline in sub. (8) (am) 1. or (b) 1. or 2. Each emission test shall follow the methods and procedures listed in s. NR 439.07. Method 18, 25 or 25A in 40 CFR part 60, Appendix A, incorporated by reference in s. NR 484.04 (16), (19) and (20), shall be used to determine the VOC concentration at the sampling points. When determining the VOC concentration, the probe shall be heated during testing to at least the exhaust gas stream temperature. (b) 1. Any facility with allowable VOC emissions from lithographic printing presses of 100 tons or more per year shall perform an emission test which that demonstrates compliance with sub. (3) (a) every 24 months. Each biennial test shall be performed within 90 days of the anniversary date of the initial emission test or an alternate date approved by the department. The testing exceptions listed in s. NR 439.075 (4) may apply to this test schedule. 2. Any facility with allowable VOC emissions from lithographic printing presses of less than 100 tons per year shall perform an initial emission test which that demonstrates compliance with sub. (3) (a) every 48 months. Each test shall be performed within 90 days of the anniversary date of the initial emission test.
SECTION 20. NR 422.143 (7) (c) is renumbered (7) (c) (intro.) and amended to read:
NR 422.143 (7) (c) The VOC content of heatset web, sheet−fed and cold set web lithographic inks the as-applied fountain solutions and cleaning solutions shall be determined in accordance with s. NR 439.06 (3) (j). by any of the following methods: SECTION 21. NR 422.143 (7) (c) 1. and 2. and (d) are created to read:
NR 422.143 (7) (c) 1. The method referred to in s. NR 439.06 (3) (j). 2. If diluted prior to use, a calculation shall be performed for VOC content that combines the method referred in s. NR 439.06(3)(j) for the concentrated materials used to prepare the as-applied fountain solution or cleaning solution, and the proportions in which they are mixed to make the as-applied fountain solution or cleaning solution. (d) The VOC composite partial vapor pressure of each cleaning solution shall be determined by any of the following methods:
1. If diluted prior to use, calculate the VOC composite vapor pressure of the as-applied solvent by using the formula for "VOC composite vapor pressure" as follows:
a. Determine the identity and quantity of each compound in a blended organic solvent.
b. Determine the vapor pressure of each pure VOC component.
c. Calculate the VOC composite partial pressure of the solvent by using the formula for "VOC composite partial pressure." For the purpose of this calculation, the blended solvent shall be assumed to be an ideal solution where "Raoult's Law" applies. The partial vapor pressures of each compound at 68ºF shall be used in the formula. The VOC composite partial pressure shall be calculated as follows: where:
Wi is the weight of the "i"th VOC compound, in grams.
Ww is the weight of water, in grams.
We is the weight of exempt compound, in grams.
MWi is the molecular weight of the "i"th VOC compound, in grams per gram-mole.
MWw is the molecular weight of water, in grams per gram-mole.
MWe is the molecular weight of the "e"th exempt compound, in grams per gram-mole.
PPc is the VOC composite vapor pressure at 68ºF, in mm Hg.
VPi is the vapor pressure of the "i"th VOC compound at 68ºF, in mm Hg.
2. If not diluted prior to use, the owner or operator shall use formulation information provided by the supplier, such as a safety data sheet (SDS) or equivalent information from the supplier as long as it is based on results determined in accordance with the procedure in sub. (7) (d) 1.
SECTION 22. NR 422.143 (8) (a) and (b) (title) are repealed.
SECTION 23. NR 422.143 (8) (b) 1. is renumbered NR 422.143 (8) (am), and amended to read:
NR 422.143 (8) (am) The owner or operator of a heatset web lithographic printing press which that is installed after May 1, 2010 the effective date of this rule [LRB inserts date] shall perform a compliance emission test within 180 days after installation of the press and shall submit to the department no later than 60 days after the test written certification that the press is in compliance with the applicable requirements of subs. sub. (3) and (6) and a demonstration of compliance in accordance with subs. (6), (7), and (8).
SECTION 24. NR 422.143 (8) (b) 2. is renumbered NR 422.143 (8) (bm), and amended to read:
NR 422.143 (8) (bm) The owner or operator of any lithographic printing press, other than a heatset web press, which that is installed after May 1, 2010 the effective date of this rule [LRB inserts date] shall submit to the department, no later than 180 days after installation of the press, written certification that the press is in compliance with the applicable requirements of subs. sub. (3) and (6) and a demonstration of compliance in accordance with subs. (6), (7), and (8).
SECTION 25. NR 422.143 (8) (c) is created to read:
NR 422.143 (8) (c) Facilities subject to this section and located in an area described under sub. (1) (a) 2. c., shall comply with the applicable requirements of this section by the following deadlines:
1. Facilities that were initially constructed in an area described in sub. (1) (a) 2. c., prior to the effective date of its designation as moderate, serious, severe, or extreme ozone nonattainment, shall comply with applicable requirements within 180 days of the effective date of designation.
2. Facilities that were initially constructed in an area described in sub. (1) (a) 2. c., after the area has been designated as moderate, serious, severe, or extreme ozone nonattainment, shall comply with applicable requirements upon startup.
SECTION 26. EFFECTIVE DATE. This rule shall take effect on the first day of the month following publication in the Wisconsin administrative register as provided in s. 227.22 (2) (intro.), Stats. SECTION 27. BOARD ADOPTION. This rule was approved and adopted by the State of Wisconsin Natural Resources Board on January 23, 2019.
Dated at Madison, Wisconsin _________________________________.
STATE OF WISCONSIN
DEPARTMENT OF NATURAL RESOURCES
By__________________________________
Preston D. Cole, Secretary
(SEAL)
