←———Length ——————→
A. The vegetative buffer shall be located along the entire length of the down slope edge of the entire disturbed area for which the practice is being applied.
B. The vegetative buffer shall be located on the contour.
C. The width of the vegetative buffer shall have slopes less than 5%.
D. The disturbed area draining to the vegetative buffer shall have slopes of 6% or less.
E. The vegetative buffer shall have a minimum width of 25 feet. 25 feet is adequate for disturbed areas up to 125 feet upslope from the vegetative buffer. An additional one foot of width shall be added to the buffer for every 5 feet exceeding 125 feet upslope of the disturbed area draining to the vegetative buffer.
F. To minimize compaction and destruction of the vegetative cover, designate the vegetative buffer as an area of no disturbance. Construction equipment shall be excluded from the designated area. Vegetative buffers shall be clearly shown on plans and marked in the field.
G. Vegetative buffers shall be densely vegetated prior to upslope soil disturbance.
VI. Considerations
A. Maintaining sheet flow is critical to the function of a vegetative buffer. In some conditions, a level spreader may need to be constructed at the upslope side of the vegetative buffer to minimize concentrated flow.
B. Vegetative buffers may require large land areas compared to other erosion control practices.
C. Trees should not be cut down to establish a vegetative buffer. Other erosion control measures are preferred.
VII. Plans and Specifications
A. Plans and specifications for vegetative buffers shall be in keeping with this standard and shall describe the requirements for applying the practice to achieve its intended purpose. The plans and specifications shall address the following:
1. Location of vegetative buffer.
2. Limits and slopes of disturbed area and any additional contributory drainage area.
3. Dimensions and slope of vegetative buffer.
B. All plans, standard detail drawings, or specifications shall include schedule for installation, inspection, and maintenance. The responsible party shall be identified.
VIII. Operation and Maintenance
A. Vegetative buffers shall be inspected for proper distribution of flows, sediment accumulation and signs of rill formation. Vegetative buffers shall at a minimum be inspected weekly and within 24 hours after every precipitation event that produces 0.5 inches of rain or more during a 24-hour period.
B. If the vegetative buffer becomes silt covered, contains rills, or is otherwise rendered ineffective, other perimeter sediment control measures shall be installed. Eroded areas shall be repaired and stabilized. Repair shall be completed as soon as possible with consideration to site conditions.
C. A stand of dense vegetation shall be maintained to a height of 3–12 inches.
D. Prior to land disturbance the perimeter of vegetative buffers shall be flagged or fenced to prevent equipment from creating ruts, compacting the soil and to prevent damage to vegetation.
IX. Definitions
Dense vegetation (I): is defined as an existing stand of 3–12 inch high grassy vegetation that uniformly covers at least 90 % of a representative 1 square yard plot. Woody vegetation shall not be counted for the 90% coverage. No more than 10% of the overall buffer can be comprised of woody vegetation.
Level Spreader (VI.A): Level spreaders disperse flows over a wide area, dissipating the energy of the runoff and creating sheet flow. Common types of level spreaders are weirs and stone trenches.
Sheetflow (II): Sheet flow is over plane surfaces, where runoff water flows in a thin uniform sheet across the land before it collects in a concentrated flow.
Sheet and Rill Erosion (III): Sheet and rill erosion is the removal of soil by the action of rainfall and shallow overland runoff. It is the first stage in water erosion. As flow becomes more concentrated rills occur. As soil detachment continues or flow increases, rills will become wider and deeper.
Width (V.E): Is measured in the direction of flow.
Frost-Protected Shallow Footings
In lieu of frost walls, the code recognizes frost-protected shallow foundations designed per ASCE 32, "Design and Construction of Frost-Protected Shallow Foundations". The department also recognizes the similar design standards of U.S.HUD "Design Guide for Frost-Protected Shallow Foundations", available for free download from
www.huduser.org/publications/destech/desguide.html and summarized below. Consult it or the ASCE standard for full design and installation information, including a more flexible, detailed design method that should be used for heated buldings with attached, unheated garages.
Note that both standards offer design methods for both heated and unheated buildings. For heated buildings, the designs rely upon containing the building's heat under the footings to avoid frost heaving. In the case of unheated buildings, the designs rely upon containing the earth's natural warmth under the footings and slab by the use of more extensive insulation. (For both design approaches, compliance with their frost-protection requirements is not necessarily the same as compliance with the ch.
SPS 322 Energy Conservation standards for slab-on-grade designs.)
Because the simplified heated building design methods rely upon buildings, including attached garages, with at least a 63 degree internal temperature, it is important the building designer consult with the owner regarding their intended use. Even if the initial owner plans to keep the building heated throughout the winter, future owners may use it otherwise. Therefore, the designer should be sure to communicate the operational needs of the building through means such as building placarding, notating the Rescheck Energy Report, and/or recording relevant information on the property deed. Failure to do so may cause severe structural damage to the building if future owners do not keep the building heated.
Unheated Building Design
1 Also see s.
SPS 322.33 for additional slab-edge insulation requirements.
2 Units are degrees Fahrenheit. See estimate provided on Mean Annual Temperature Contour Map.
3 Air freezing index shall be based on maximum year expected for a 100-year return period. See estimate provided on AFI Contour Map.
4 Ground insulation to the building interior can be extended beneath the entire slab where it is desired to protect the entire slab from frost heave action.
5 Ground insulation to the building interior can be in one horizontal plane (as shown in the detail) and covered with non frost-susceptible fill or the insulation maybe placed directly beneath the slab.
6 Insulation thickness recommendations are for extruded polystyrene (XPS) insulation.
7 The minimum depth of concrete footing and horizontal insulation is 10‶. A 6‶ drainage layer is required under the insulation.
8 Insulation placed directly beneath the footing shall be Type IV or Type VI XPS in accordance with ASTM C578. Maximum deadload placed on the Type IV insulation shall be 1200 pounds/square foot. Maximum deadload placed on Type VI shall be 1900 psf.
Heated Building Design
Minimum Insulation Requirements for Frost-Protected Footings in Heated Buildings1
(Simplified Method)
-
See PDF for table ![PDF](https://docs-preview.legis.wisconsin.gov/assets/image/file_acrobat.gif)
1 Insulation requirements are for protection against frost damage in heated buildings. Greater values may be required to meet energy conservation standards. Interpolation between values is permissible.
2 See AFI Contour Map for Air Freezing Index values.
3 Insulation materials shall provide the stated minimum R-values under long-term exposure to moist, below-ground conditions in freezing climates. The following R-values shall be used to determine insulation thicknesses required for this application: Type II expanded polystyrene - 2.4R per inch; Types IV, V, VI, VII extruded polystyrene - 4.5R per inch; Type IX expanded polystyrene - 3.2R per inch. NR indicates that insulation is not required.
4 Vertical insulation shall be expanded polystyrene insulation or extruded polystyrene insulation.
5 Horizontal insulation shall be extruded polystyrene insulation.