- Use of data from precompliance tests;
- Use of data from previous compliance tests; and
- Use of data from similar facilities.
(3) This step does not apply to precompliance procedures.
(4) Prepare certification of precompliance.
• Calculate the “conservative" dust metal concentration limit (DMCLc) using Equation 5.
• Submit certification of precompliance. This certification shall include precompliance limits for all compliance parameters that apply to other boilers and industrial furnaces (i.e., those that do not recycle emission control residue back into the furnace) as listed in s.
NR 666.103(2)(c), except that it is not necessary to set precompliance limits on maximum feedrate of each hazardous metal in all combined feedstreams.
• Furnaces that recycle collected PM back into the furnace (and that elect to comply with this method (see s.
NR 666.103(3)(c)2.) are subject to a special precompliance parameter, however. They shall establish precompliance limits on the maximum concentration of each hazardous metal in collected kiln dust (which shall be set according to the procedures described above).
(5) Monitor metal concentration in kiln dust for continuing compliance, and maintain compliance with all precompliance limits until certification of compliance has been submitted.
• Metals to be monitored during precompliance testing are classified as either “critical" or “noncritical" metals.
- All metals shall initially be classified as “critical" metals and be monitored on a daily basis.
- A “critical" metal may be reclassified as a “noncritical" metal if its concentration in the kiln dust remains below 10% of its “conservative" kiln dust metal concentration limit for 30 consecutive daily samples. “Noncritical" metals shall be monitored on a weekly basis, at a minimum.
- A “noncritical" metal shall be reclassified as a “critical" metal if its concentration in the kiln dust is above 10% of its “conservative" kiln dust metal concentration limit for any single daily or weekly sample.
• It is a violation if the facility fails to analyze the kiln dust for any “critical" metal on any single day or for any “noncritical" metal during any single week, when hazardous waste is burned.
• Follow the sampling, compositing, and analytical procedures described in this method and in other appropriate methods, as they pertain to the condition and accessibility of the kiln dust.
• Samples shall be collected at least once every 8 hours, and a daily composite prepared according to appropriate procedures.
- At least one composite sample is required. This sample is referred to as the “required" sample.
- For QA/QC purposes, a facility may elect to collect 2 or more additional samples. These samples are referred to as the “spare" samples. These additional samples shall be collected over the same time period and according to the same procedures as those used for the “required" sample.
- Samples for “critical" metals shall be daily composites.
- Samples for “noncritical" metals shall be weekly composites, at a minimum. These samples can be composites of the original 8-hour samples, or they can be composites of daily composite samples.
• Analyze the “required" sample to determine the concentration of each metal.
- This analysis shall be completed within 48 hours of the close of the sampling period. Failure to meet this schedule is a violation.
• If the “conservative" kiln dust metal concentration limit is exceeded for any metal, refer to Step 8.
• If the “conservative" kiln dust metal concentration limit is not exceeded, continue with the daily and/or weekly monitoring (Step 5) for the duration of interim license.
(6) This step does not apply to precompliance procedures.
(7) This step does not apply to precompliance procedures.
(8) If the “conservative" kiln dust metal concentration limit was exceeded for any metal in any single analysis of the “required" kiln dust sample, the “spare" samples corresponding to the same period may be analyzed to determine if the exceedance is due to a sampling or analysis error.
• If no “spare" samples were taken, refer to Step 9.
• If the average of all the samples for a given day (or week, as applicable) (including the “required" sample and the “spare" samples) does not exceed the “conservative" kiln dust metal concentration limit, no corrective measures are necessary; continue with the daily and/or weekly monitoring as described in Step 5.
• If the average of all the samples for a given day (or week, as applicable) exceeds the “conservative" kiln dust metal concentration limit, but the average of the “spare" samples is below the “conservative" kiln dust metal concentration limit, apply the Q-test, described in Appendix A, to determine whether the “required" sample concentration can be judged as an outlier.
- If the “required" sample concentration is judged an outlier, no corrective measures are necessary; continue with the daily and/or weekly monitoring described in Step 5.
- If the “required" sample concentration is not judged an outlier, refer to Step 10.
(9) This step does not apply to precompliance procedures.
(10) Determine if the “conservative" kiln dust metal concentration limit has been exceeded more than 3 times in the last 60 days.
• If not, log this exceedance and continue with the daily and/or weekly monitoring (Step 5).
• If so, the tests to determine the enrichment factors shall be repeated (refer to Step 11).
• This determination is made separately for each metal; for example:
- Three exceedances for each of the 10 hazardous metals are allowed within any 60-day period.
- Four exceedances of any single metal in any 60-day period is not allowed.
• This determination should be made daily, beginning on the first day of daily monitoring. For example, if 4 exceedances of any single metal occur in the first 4 days of daily monitoring, do not wait until the end of the 60-day period; refer immediately to Step 11.
(11) A revised certification of precompliance shall be submitted to the department (or certification of compliance shall be submitted) if: (1) More than 3 exceedances of the “conservative" kiln dust metal concentration limit occur within any 60 consecutive daily samples; or (2) an exceedance of the “conservative" kiln dust metal concentration limit occurs in any weekly sample.
• The facility shall notify the department if a revised certification of precompliance shall be submitted.
• The facility has up to 720 waste-burning hours to submit a certification of compliance or a revised certification of precompliance. During this period, the feed rate of the metal in violation shall be reduced by 50%. In the case of a revised certification of precompliance, engineering judgement shall be used to ensure that the “conservative" kiln dust metal concentration will not be exceeded. Examples of how this goal might be accomplished include:
- Changing equipment or operating procedures to reduce the kiln dust metal concentration;
- Changing equipment or operating procedures, or using more detailed engineering judgement, to decrease the estimated SEF and thus increase the “conservative" kiln dust metal concentration limit;
- Increasing the “conservative" kiln dust metal concentration limit by imposing a stricter PM emissions standard; or
- Increasing the “conservative" kiln dust metal concentration limit by performing a more detailed risk assessment to increase the metal emission limits.
• Meanwhile, the facility shall continue with daily kiln dust metals monitoring (Step 5).
Appendix A to Appendix IX—Statistics
A.1 Determination of Enrichment Factor
After at least 10 initial emissions tests are performed, an enrichment factor for each metal shall be determined. At the 95% confidence level, the enrichment factor, EF95% s, is based on the test results and is statistically determined so there is only a 5% chance that the enrichment factor at any given time will be larger than EF95% . Similarly, at the 99% confidence level, the enrichment factor, EF99% , is statistically determined so there is only a 1% chance that the enrichment factor at any given time will be larger than EF99% .
For a large number of samples (n > 30), EF95% is based on a normal distribution, and is equal to:
EF95% = EF + zc ó
(1)
where:
For a 95% confidence level, zc is equal to 1.645.
For a small number of samples (n<30), EF95% is based on the t-distribution and is equal to:
EF95% = EF + tc S
(4)
where the standard deviation, S, is defined as:
tc is a function of the number of samples and the confidence level that is desired. It increases in value as the sample size decreases and the confidence level increases. The 95% confidence level is used in this method to calculate the “violation" kiln dust metal concentration limit; and the 99% confidence level is sometimes used to calculate the “conservative" kiln dust metal concentration limit. Values of tc are shown in table A-1 for various degrees of freedom (degrees of freedom = sample size-1) at the 95% and 99% confidence levels. As the sample size approaches infinity, the normal distribution is approached.
A.2 Comparison of Enrichment Factor Groups
To determine if the enrichment factors measured in the quarterly tests are significantly different from the enrichment factors determined in the initial Step 2 tests, the t-test is used. In this test, the value tmeas:
is compared to tcrit at the desired confidence level. The 95% confidence level is used in this method. Values of tcrit are shown in table A-1 for various degrees of freedom (degrees of freedom n
1+n2-2) at the 95% and 99% confidence levels. If tmeas is greater then tcrit, it can be concluded with 95% confidence that the 2 groups are not from the same population.
A.3 Rejection of Data
If the concentration of any hazardous metal in the “required" kiln dust sample exceeds the kiln dust metal concentration limit, the “spare" samples are analyzed. If the average of the combined “required" and “spare" values is still above the limit, a statistical test is used to decide if the upper value can be rejected.
The “Q-test" is used to determine if a data point can be rejected. The difference between the questionable result and its neighbor is divided by the spread of the entire data set. The resulting ratio, Qmeas, is then compared with rejection values that are critical for a particular degree of confidence, where Qmeas is:
The 90% confidence level for data rejection is used in this method. Table A-2 provides the values of Q
crit at the 90% confidence level. If Q
meas is larger than Q
crit, the data point can be discarded. Only one data point from a sample group can be rejected using this method.
-
See PDF for table 
