NR 661.0020(1)(1)
A solid waste, as defined in s.
NR 661.0002, that is not excluded from regulation as a hazardous waste under s.
NR 661.0004 (2), is a hazardous waste if it exhibits any of the characteristics identified in this subchapter.
NR 661.0020 Note
Note: Section
NR 662.011 sets forth the generator's responsibility to determine whether its waste exhibits one or more of the characteristics identified in this subchapter.
NR 661.0020(2)
(2) A hazardous waste that is identified by a characteristic in this subchapter is assigned every EPA hazardous waste number that is applicable as set forth in this subchapter. This number shall be used in complying with the notification requirements under s.
NR 660.07 and all applicable recordkeeping and reporting requirements under chs.
NR 662 to
665,
668, and
670.
NR 661.0020(3)
(3) For the purposes of this subchapter, the department will consider a sample obtained using any of the applicable sampling methods specified in ch.
NR 661 Appendix I to be a representative sample within the meaning specified in ch.
NR 660.10 (101).
NR 661.0020 Note
Note: Since ch.
NR 661 Appendix I sampling methods are not being adopted by the department, a person who desires to employ an alternative sampling method is not required to demonstrate the equivalency of the method under the procedures set forth in ss.
NR 660.20 and
660.21.
NR 661.0020 History
History: CR 19-082: cr.
Register August 2020 No. 776, eff. 9-1-20; correction in (3) made under s.
35.17, Stats.,
Register August 2020 No. 776.
NR 661.0021
NR 661.0021 Characteristic of ignitability. NR 661.0021(1)(1)
A solid waste exhibits the characteristic of ignitability if a representative sample of the waste has any of the following properties:
NR 661.0021(1)(a)
(a) It is a liquid, other than an aqueous solution containing less than 24 percent alcohol by volume, and has flash point less than 60
°C or 140
°F, as determined by a Pensky-Martens Closed Cup Tester, using the test method specified in ASTM Standard D 93-79 or D 93-80, incorporated by reference in s.
NR 660.11, or a Setaflash Closed Cup Tester, using the test method specified in ASTM Standard D 3278-78, incorporated by reference in s.
NR 660.11.
NR 661.0021(1)(b)
(b) It is not a liquid and is capable, under standard temperature and pressure, of causing fire through friction, absorption of moisture or spontaneous chemical changes and, when ignited, burns so vigorously and persistently that it creates a hazard.
NR 661.0021(2)
(2) A solid waste that exhibits the characteristic of ignitability has the EPA hazardous waste number of D001.
NR 661.0021 History
History: CR 19-082: cr.
Register August 2020 No. 776, eff. 9-1-20; correction in (1) (a) made under s.
35.17, Stats.,
Register August 2020 No. 776.
NR 661.0022(1)(1)
A solid waste exhibits the characteristic of corrosivity if a representative sample of the waste has either of the following properties:
NR 661.0022(1)(a)
(a) It is aqueous and has a pH less than or equal to 2 or greater than or equal to 12.5, as determined by a pH meter using Method 9040C in “Test Methods for Evaluating Solid Waste, Physical/Chemical Methods,” EPA Publication SW-846, as incorporated by reference in s.
NR 660.11.
NR 661.0022(1)(b)
(b) It is a liquid and corrodes SAE 1020 steel at a rate greater than 6.35 mm per year at a test temperature of 55
°C as determined by Method 1110A in “Test Methods for Evaluating Solid Waste, Physical/Chemical Methods,” EPA Publication SW-846, and as incorporated by reference in s.
NR 660.11.
NR 661.0022(2)
(2) A solid waste that exhibits the characteristic of corrosivity has the EPA hazardous waste number of D002.
NR 661.0022 History
History: CR 19-082: cr.
Register August 2020 No. 776, eff. 9-1-20.
NR 661.0023(1)(1)
A solid waste exhibits the characteristic of reactivity if a representative sample of the waste has any of the following properties:
NR 661.0023(1)(a)
(a) It is normally unstable and readily undergoes violent change without detonating.
NR 661.0023(1)(d)
(d) When mixed with water, it generates toxic gases, vapors or fumes in a quantity sufficient to present a danger to human health or the environment.
NR 661.0023(1)(e)
(e) It is a cyanide or sulfide bearing waste which, when exposed to pH conditions between 2 and 12.5, can generate toxic gases, vapors or fumes in a quantity sufficient to present a danger to human health or the environment.
NR 661.0023(1)(f)
(f) It is capable of detonation or explosive reaction if it is subjected to a strong initiating source or if heated under confinement.
NR 661.0023(1)(g)
(g) It is readily capable of detonation or explosive decomposition or reaction at standard temperature and pressure.
NR 661.0023(2)
(2) A solid waste that exhibits the characteristic of reactivity has the EPA hazardous waste number of D003.
NR 661.0023 History
History: CR 19-082: cr.
Register August 2020 No. 776, eff. 9-1-20; correction in (1) (h) made under s.
35.17, Stats.,
Register August 2020 No. 776.
NR 661.0024(1)(1)
A solid waste, except manufactured gas plant waste, exhibits the characteristic of toxicity if, using the Toxicity Characteristic leaching procedure, test Method 1311 in “Test Methods for Evaluating Solid Waste, Physical/Chemical Methods,” EPA Publication SW-846, as incorporated by reference in s.
NR 660.11, the extract from a representative sample of the waste contains any of the contaminants listed in Table 2 at the concentration equal to or greater than the respective value given in that table. Where the waste contains less than 0.5 percent filterable solids, the waste itself, after filtering using the methodology outlined in Method 1311, is considered to be the extract for the purpose of this section.
NR 661.0024(2)
(2) A solid waste that exhibits the characteristic of toxicity has the EPA hazardous waste number specified in Table 1 which corresponds to the toxic contaminant causing it to be hazardous.
Table 1
Maximum Concentration of Contaminants for the Toxicity Characteristic
- See PDF for table 
1Hazardous waste number.
2Chemical abstracts service number.
3If o-, m-, and p-Cresol concentrations cannot be differentiated, the total cresol, D026, concentration is used. The regulatory level of total cresol is 200 mg/l.
4Quantitation limit is greater than the calculated regulatory level. The quantitation limit therefore becomes the regulatory level.
NR 661.0024 History
History: CR 19-082: cr.
Register August 2020 No. 776, eff. 9-1-20.
NR 661.0030(1)(1)
A solid waste is a hazardous waste if it is listed in this subchapter, unless it has been excluded from this list under ss.
NR 660.20 and
660.22.
NR 661.0030(2)
(2) The department will indicate the department's basis for listing the classes or types of wastes listed in this subchapter by employing one or more of the following hazard codes:
-
See PDF for table NR 661.0030 Note
Note: Chapter
NR 661 Appendix VII identifies the constituent that caused the department to list the waste as a Toxicity Characteristic waste by the letter `E' or toxic waste by the letter `T' in ss.
NR 661.0031 and
661.0032.
NR 661.0030(3)
(3) Each hazardous waste listed in this subchapter is assigned an EPA hazardous waste number that precedes the name of the waste. This number shall be used in complying with the notification requirements under s.
NR 660.07 and certain recordkeeping and reporting requirements under chs.
NR 662 to
670.
NR 661.0030(4)
(4) The following hazardous wastes listed in s.
NR 661.0031 are subject to the exclusion limits for acutely hazardous wastes established in s.
NR 662.013: EPA hazardous wastes numbers F020, F021, F022, F023, F026 and F027.
NR 661.0030 History
History: CR 19-082: cr.
Register August 2020 No. 776, eff. 9-1-20.
NR 661.0031
NR 661.0031 Hazardous wastes from non-specific sources. NR 661.0031(2)(a)
(a) For the purposes of the F037 and F038 listings, oil or water or solids is defined as any combination of oil, water, or solids.
NR 661.0031(2)(b)1.1. For the purposes of the F037 and F038 listings, aggressive biological treatment units are defined as units which employ one of the following 4 treatment methods: activated sludge; trickling filter; rotating biological contactor for the continuous accelerated biological oxidation of wastewaters; or high-rate aeration. High-rate aeration is a system of surface impoundments or tanks, in which intense mechanical aeration is used to completely mix the wastes, enhance biological activity, and the units employ a minimum of 6 hp per million gallons of treatment volume; and either the hydraulic retention time of the unit is no longer than 5 days; or the hydraulic retention time is no longer than 30 days and the unit does not generate a sludge that is a hazardous waste by the Toxicity Characteristic.
NR 661.0031(2)(b)2.
2. Generators and treatment, storage and disposal facilities have the burden of proving that their sludges are exempt from listing as F037 and F038 wastes under subd.
1. Generators and treatment, storage and disposal facilities shall maintain, in their operating or other on-site records, documents and data sufficient to prove that the unit is an aggressive biological treatment unit as defined in this subsection; and the sludges sought to be exempted from the definitions of F037 or F038 were generated in the aggressive biological treatment unit.
NR 661.0031(2)(c)1.1. For the purposes of the F037 listing, sludges are considered to be generated at the moment of deposition in the unit, where deposition is defined as at least a temporary cessation of lateral particle movement.
NR 661.0031(2)(c)2.
2. For the purposes of the F038 listing, sludges are considered to be generated at the moment of deposition in the unit, where deposition is defined as at least a temporary cessation of lateral particle movement and floats are considered to be generated at the moment they are formed in the top of the unit.
NR 661.0031(2)(d)
(d) For the purposes of the F019 listing, the following apply to wastewater treatment sludges from the manufacturing of motor vehicles using a zinc phosphating process:
NR 661.0031(2)(d)1.
1. Motor vehicle manufacturing is defined to include the manufacture of automobiles and light trucks or utility vehicles, including light duty vans, pick-up trucks, minivans, and sport utility vehicles. Facilities shall be engaged in manufacturing complete vehicles, body and chassis or unibody, or chassis only.
NR 661.0031(2)(d)2.
2. A generator shall maintain in its on-site records documentation and information sufficient to prove that the wastewater treatment sludges to be exempted from the F019 listing meet the conditions of the listing. These records include all of the following: the volume of waste generated and disposed of off-site; documentation showing when the waste volumes were generated and sent off site; the name and address of the receiving facility; and documentation confirming receipt of the waste by the receiving facility. A generator shall maintain these documents on site for no less than 3 years. The retention period for the documentation is automatically extended during the course of any enforcement action or as requested by the department.
NR 661.0031 History
History: CR 19-082: cr.
Register August 2020 No. 776, eff. 9-1-20; correction in (Table) made under s.
35.17, Stats.,
Register August 2020 No. 776.
NR 661.0032
NR 661.0032 Hazardous wastes from specific sources. NR 661.0032(2)
(2)
Listing specific definitions.
For the purposes of the K181 listing under sub.
(3), dyes or pigments production is defined to include manufacture of the following product classes: dyes, pigments, or FDA certified colors that are classified as azo, triarylmethane, perylene or anthraquinone classes. Azo products include azo, monoazo, diazo, triazo, polyazo, azoic, benzidine, and pyrazolone products. Triarylmethane products include both triarylmethane and triphenylmethane products. Wastes that are not generated at a dyes or pigments manufacturing site, such as wastes from the off-site use, formulation, and packaging of dyes or pigments, are not included in the K181 listing.
NR 661.0032(3)
(3)
K181 listing levels.
Nonwastewaters containing constituents in amounts equal to or exceeding the following levels during any calendar year are subject to the K181 listing, unless the conditions in the K181 listing are met.
-
See PDF for table NR 661.0032(4)
(4)
Procedures for demonstrating that dyes or pigment nonwastewaters are not K181. The procedures described in pars.
(a) to
(c) and
(e) establish when nonwastewaters from the production of dyes or pigments would not be hazardous. These procedures apply to wastes that are not disposed in landfill units or treated in combustion units as specified in sub.
(1). If the nonwastewaters are disposed in landfill units or treated in combustion units as described in sub.
(1), then the nonwastewaters are not hazardous. In order to demonstrate that it is meeting the landfill disposal or combustion conditions contained in the K181 listing description, the generator shall maintain documentation as described in par.
(d).
NR 661.0032(4)(a)
(a)
Determination based on no K181 constituents. A generator that has knowledge, such as knowledge of constituents in wastes based on prior sampling and analysis data or information about raw materials used, production processes used, and reaction and degradation products formed, that its wastes contain none of the K181 constituents listed in sub
. (3) can use its knowledge to determine that its waste is not K181. The generator shall document the basis for all such determinations on an annual basis and keep each annual documentation for 3 years.
NR 661.0032(4)(b)
(b)
Determination for generated quantities of 1,000 metric tons a year or less for wastes that contain K181 constituents. If the total annual quantity of dyes or pigment nonwastewaters generated is 1,000 metric tons or less, the generator can use knowledge of the wastes, such as knowledge of constituents in wastes based on prior analytical data or information about raw materials used, production processes used, and reaction and degradation products formed, to conclude that annual mass loadings for the K181 constituents are below the listing levels of sub.
(3). To make this determination, the generator shall do all of the following:
NR 661.0032(4)(b)1.
1. Each year document the basis for determining that the annual quantity of nonwastewaters expected to be generated will be less than 1,000 metric tons.
NR 661.0032(4)(b)2.
2. Track the actual quantity of nonwastewaters generated from January 1 through December 31 of each year. If, at any time within the year, the actual waste quantity exceeds 1,000 metric tons, the generator shall comply with the requirements under par.
(c) for the remainder of the year.
NR 661.0032(4)(b)3.
3. Keep a running total of the K181 constituent mass loadings over the course of the calendar year.
NR 661.0032(4)(b)4.
4. Keep all of the following records on-site for the 3 most recent calendar years in which the hazardous waste determinations are made:
NR 661.0032(4)(b)4.c.
c. The calculations performed to determine annual total mass loadings for each K181 constituent in the nonwastewaters during the year.
NR 661.0032(4)(c)
(c)
Determination for generated quantities greater than 1,000 metric tons a year for wastes that contain K181 constituents.
If the total annual quantity of dyes or pigment nonwastewaters generated is greater than 1,000 metric tons, the generator shall perform all of the following steps in order to make a determination that its waste is not K181:
NR 661.0032(4)(c)1.
1. Determine which K181 constituents listed in sub
. (3) are reasonably expected to be present in the wastes based on knowledge of the wastes, such as based on prior sampling and analysis data or information about raw materials used, production processes used, and reaction and degradation products formed.
NR 661.0032(4)(c)2.
2. If 1,2-phenylenediamine is present in the wastes, the generator can use either knowledge or sampling and analysis procedures to determine the level of this constituent in the wastes. For determinations based on use of knowledge, the generator shall comply with the procedures for using knowledge described in par.
(b) and keep the records described in par.
(b) 4. For determinations based on sampling and analysis, the generator shall comply with all of the sampling and analysis and recordkeeping requirements in subds.
3. to
11. NR 661.0032(4)(c)3.
3. Develop a waste sampling and analysis plan or modify an existing plan to collect and analyze representative waste samples for the K181 constituents reasonably expected to be present in the wastes. At a minimum, the plan shall include all of the following:
NR 661.0032(4)(c)3.c.
c. A discussion of how the sampling plan accounts for potential temporal and spatial variability of the wastes.
NR 661.0032(4)(c)3.d.
d. A detailed description of the test methods to be used, including sample preparation, clean up, if necessary, and determinative methods.
NR 661.0032(4)(c)4.
4. Collect and analyze samples in accordance with the waste sampling and analysis plan.
NR 661.0032(4)(c)4.a.
a. The sampling and analysis shall be unbiased, precise, and representative of the wastes.
