NR 440.66(2)(b)
(b) “Equipment" means each valve, pump, pressure relief device, sampling connection system, open-ended valve or line and flange or other connector in VOC service. Compressors are considered equipment only for the purposes of recordkeeping and reporting.
NR 440.66(2)(c)
(c) “In hydrogen service" means that a compressor contains a process fluid that meets the conditions in
sub. (4) (b).
NR 440.66(2)(d)
(d) “In light liquid service" means that the piece of equipment contains a liquid that meets the conditions specified in
sub. (4) (c).
NR 440.66(2)(e)
(e) “Petroleum refinery" means that facility engaged in producing gasoline, kerosene, distillate fuel oils, residual fuel oils, lubricants, or other products through the distillation of petroleum or through the redistillation, cracking, or reforming of unfinished petroleum derivatives.
NR 440.66(2)(f)
(f) “Petroleum" means the crude oil removed from the earth and the oils derived from tar sands, shale and coal.
NR 440.66(2)(g)
(g) “Process unit" means components assembled to produce intermediate or final products from petroleum, unfinished petroleum derivatives, or other intermediates; a process unit can operate independently if supplied with sufficient feed or raw materials and sufficient storage facilities for the product.
NR 440.66(3)(a)(a) Each owner or operator subject to the provisions of this section shall comply with the requirements of
s. NR 440.62 (3) (a) to
(j) as soon as practicable, but no later than 180 days after initial startup.
NR 440.66(3)(c)
(c) An owner or operator may apply to the administrator for a determination of equivalency for any means of emission limitation that achieves a reduction in emissions of VOC at least equivalent to the reduction in emissions of VOC achieved by the controls required in this section. In doing so the owner or operator shall comply with requirements
40 CFR 60.484, as in effect on July 1, 1994, and provide notice to the department of any determination of equivalency approved by the administrator.
NR 440.66(3)(d)
(d) Each owner or operator subject to the provisions of this section shall comply with the provisions of
s. NR 440.62 (6) except as provided in
sub. (4).
NR 440.66(4)(a)(a) Each owner or operator subject to the provisions of this section may comply with the following exceptions to the provisions of
s. NR 440.62.
NR 440.66(4)(b)1.1. Compressors in hydrogen service are exempt from the requirements of
sub. (3) if an owner or operator demonstrates that a compressor is in hydrogen service.
NR 440.66(4)(b)2.
2. Each compressor is presumed not to be in hydrogen service unless an owner or operator demonstrates that the piece of equipment is in hydrogen service. For a piece of equipment to be considered in hydrogen service it shall be determined that the percent hydrogen content can be reasonably expected always to exceed 50% by volume. For purposes of determining the percent hydrogen content in the process fluid that is contained in or contacts a compressor procedures that conform to the general method described in ASTM E260-96, E168-92 or E169-93, incorporated by reference in (2) (a) 75., 73. and 74., respectively, shall be used.
NR 440.66(4)(b)3.a.a. An owner or operator may use engineering judgment rather than procedures in
subd. 2. to demonstrate that the percent content exceeds 50% by volume. When an owner or operator and the department do not agree on whether a piece of equipment is in hydrogen service however, the procedure in
subd. 2. shall be used to resolve the disagreement.
NR 440.66(4)(b)3.b.
b. If an owner or operator determines that a piece of equipment is in hydrogen service the determination can be revised only after following the procedures in
subd. 2.
NR 440.66(4)(d)
(d) An owner or operator may use the following provision in addition to
s. NR 440.62 (6) (e): Equipment is in light liquid service if the percent evaporated is greater than 10% at 150
°C as determined by ASTM D86-96, incorporated by reference in
s. NR 440.17 (2) (a) 7.
NR 440.66 History
History: Cr.
Register, September, 1986, No. 369, eff. 10-1-86; am. (1) (c) (2) (intro.), (3) (c), (4) (b) 2. and (a),
Register, September, 1990, No. 417, eff. 10-1-90
; am. (3) (c),
Register, December, 1995, No. 480, eff. 1-1-96;
CR 06-109: am. (title), and (4) (b) 2. and (d) Register May 2008 No. 629, eff. 6-1-08.
NR 440.67
NR 440.67 Synthetic fiber production facilities. NR 440.67(1)(1)
Applicability and designation of affected facility. NR 440.67(1)(a)(a) Except as provided in
par. (b), the affected facility to which the provisions of this section apply is each solvent-spun synthetic fiber process that produces more than 500 Mg (551 ton) of fiber per year.
NR 440.67(1)(b)
(b) The provisions of this section do not apply to any facility that uses the reaction spinning process to produce spandex fiber or the viscose process to produce rayon fiber.
NR 440.67(1)(c)
(c) The provisions of this section apply to each facility as identified in
par. (a) that commences construction or reconstruction after November 23, 1982. The provisions of this section do not apply to facilities that commence modification but not reconstruction after November 23, 1982.
NR 440.67(2)
(2) Definitions. As used in this section, terms not defined in this subsection have the meanings given in
s. NR 440.02.
NR 440.67(2)(a)
(a) “Acrylic fiber" means a manufactured synthetic fiber in which the fiber-forming substance is any long-chain synthetic polymer composed of at least 85% by weight of acrylonitrile units.
NR 440.67(2)(b)
(b) “Makeup solvent" means the solvent introduced into the affected facility that compensates for solvent lost from the affected facility during the manufacturing process.
NR 440.67(2)(c)
(c) “Nongaseous losses" means the solvent that is not volatilized during fiber production and escapes the process and is unavailable for recovery or is in a form or concentration unsuitable for economical recovery.
NR 440.67(2)(d)
(d) “Polymer" means any of the natural or synthetic compounds as usually high molecular weight that consist of many repeated links each link being a relatively light and simple molecule.
NR 440.67(2)(e)
(e) “Precipitation bath" means the water, solvent, or other chemical bath into which the polymer or prepolymer (partially reacted material) solution is extruded and causes physical or chemical changes to occur in the extruded solution to result in a semihardened polymeric fiber.
NR 440.67(2)(f)
(f) “Rayon fiber" means a manufactured fiber composed of regenerated cellulose as well as manufactured fibers composed of regenerated cellulose in which substituents have replaced not more than 5 percent of the hydrogens of the hydroxyl groups.
NR 440.67(2)(g)
(g) “Reaction spinning process" means the fiber-forming process where a prepolymer is extruded into a fluid medium and solidification takes place by chemical reaction to form the final polymeric material.
NR 440.67(2)(h)
(h) “Recovered solvent" means the solvent captured from liquid and gaseous process streams that is concentrated in a control device and that may be purified for reuse.
NR 440.67(2)(i)
(i) “Solvent feed" means that the solvent introduced into the spinning solution preparation system or precipitation bath. This feed stream includes the combination of recovered solvent and makeup solvent.
NR 440.67(2)(j)
(j) “Solvent inventory variation" means the normal changes in the total amount of solvent contained in the affected facility.
NR 440.67(2)(k)
(k) “Solvent recovery system" means the equipment associated with capture, transportation, collection, concentration and purification of organic solvents. It may include enclosures, hoods, ducting, piping, scrubbers, condensers, carbon adsorbers, distillation equipment and associated storage vessels.
NR 440.67(2)(L)
(L) “Solvent-spun synthetic fiber" means any synthetic fiber produced by a process that uses an organic solvent in the spinning solution, the precipitation bath, or processing of the spun fiber.
NR 440.67(2)(m)
(m) “Solvent-spun synthetic fiber process" means the total of all equipment having a common spinning solution preparation system or a common solvent recovery system and is used in the manufacture of solvent-spun synthetic fiber. It includes spinning solution preparation, spinning, fiber processing and solvent recovery but does not include the polymer production equipment.
NR 440.67(2)(n)
(n) “Spandex fiber" means a manufactured fiber in which the fiber-forming substance is a long chain synthetic polymer comprised of at least 85% of a segmented polyurethane.
NR 440.67(2)(o)
(o) “Spinning solution" means the mixture of polymer, prepolymer, or copolymer and additives dissolved in solvent. The solution is prepared at a viscosity and solvent-to-polymer ratio that is suitable for extrusion into fibers.
NR 440.67(2)(p)
(p) “Spinning solution preparation system" means the equipment used to prepare spinning solutions; the system includes equipment for mixing, filtering, blending and storage of the spinning solutions.
NR 440.67(2)(q)
(q) “Synthetic fiber" means any fiber composed partially or entirely of materials made by chemical synthesis or made partially or entirely from chemically-modified naturally-occurring materials.
NR 440.67(2)(r)
(r) “Viscose process" means the fiber forming process where cellulose and concentrated caustic soda are reacted to form soda or alkali cellulose. This reacts with carbon disulfide to form sodium cellulose xanthate which is then dissolved in a solution of caustic soda. The solution is spun into an acid coagulating bath after ripening. This precipitates the cellulose in the form of a regenerated cellulose filament.
NR 440.67(3)
(3) Standard for volatile organic compounds. On and after the date on which the initial performance test required to be conducted by
s. NR 440.08 is completed, no owner or operator subject to the provisions of this section may cause the discharge into the atmosphere from any affected facility that produces acrylic fibers VOC emissions that exceed 10 kg/Mg (20 lb/ton) solvent feed to the spinning solution preparation system or precipitation bath. VOC emissions from affected facilities that produce both acrylic and nonacrylic fiber types may not exceed 10 kg/Mg (20 lb/ton) solvent feed. VOC emissions from affected facilities that produce only nonacrylic fiber types may not exceed 17 kg/Mg (34 lb/ton) solvent feed. Compliance with the emission limitations is determined on a 6-month rolling average basis as described in
sub. (4).
NR 440.67(4)
(4) Performance test and compliance provisions. NR 440.67(4)(b)
(b) Each owner or operator of an affected facility shall determine compliance with the applicable standard in
sub. (3) by determining and recording monthly the VOC emissions per unit mass solvent feed from each affected facility for the current and preceding 5 consecutive calendar months and using these values to calculate the 6-month average emissions. Each calculation is considered a performance test. The owner or operator of an affected facility shall use the following procedure to determine VOC emissions for each calendar month:
NR 440.67(4)(b)1.
1. Install, calibrate, maintain, and operate monitoring devices that continuously measure and permanently record for each calendar month the amount of makeup solvent and solvent feed. These values shall be used in calculating VOC emissions according to
subd. 2. All monitoring devices, meters and peripheral equipment shall be calibrated and any error recorded. Total compounded error of the flow measuring and recording devices may not exceed 1% accuracy over the operating range. As an alternative to measuring solvent feed the owner or operator may:
NR 440.67(4)(b)1.a.
a. Measure the amount of recovered solvent returned to the solvent feed storage tanks and use the following equation to determine the amount of solvent feed:
Solvent Feed = Makeup Solvent + Recovered Solvent + Change in the Amount of Solvent Contained in the Solvent Feed Holding Tank.
NR 440.67(4)(b)1.b.
b. Measure and record the amount of polymer introduced into the affected facility and the solvent-to-polymer ratio of the spinning solutions and use the following equation to determine the amount of solvent feed: -
See PDF for diagram 
where subscript “i" denotes each particular spinning solution used during the test period; values of “i" vary from one to the total number of spinning solutions, “n," used during the calendar month.
NR 440.67(4)(b)2.
2. VOC emissions shall be determined each calendar month by use of the following equations:
where all values are for the calendar month only and where:
E is the VOC emissions in kg/Mg (lb/ton) solvent
SV is the measured or calculated volume of solvent feed in liters (gallons)
SW is the weight of solvent feed in Mg (ton)
MV is the measured volume of makeup solvent in liters (gallons)
MW is the weight of makeup in kg (lb)
N is the allowance for nongaseous losses, 13 kg/Mg (26 lb/ton) solvent feed to the spinning solution preparation system and precipitation bath. This value shall be used in all cases unless an owner or operator demonstrates to the satisfaction of the department that greater nongaseous losses occur at the affected facility. In this case, the greater value may be substituted in the equation.
SP is the fraction of measured volume that is actual solvent (excludes water)
D is the density of the solvent in kg/liter (lb/gallon)
K is a conversion factor, 1000 kg/Mg (2,000 lb/ton)
I is the allowance for solvent inventory variation or changes in the amount of solvent contained in the affected facility, kg/Mg (lb/ton) solvent feed (may be positive or negative)
IS is the amount of solvent contained in the affected facility at the beginning of test period, as determined by the owner or operator, in kg (lb)
IE is the amount of solvent contained in the affected facility at the close of the test period, as determined by the owner or operator, in kg (lb)
NR 440.67(5)(a)(a) The owner or operator of an affected facility shall submit a written report to the department of the following:
NR 440.67(5)(a)2.
2. The results of subsequent performance tests that indicate that VOC emissions exceed the standards in
sub. (3). These reports shall be submitted quarterly at 3-month intervals after the initial performance test. If no exceedances occur during a particular quarter, a report stating this shall be submitted to the department semiannually.
NR 440.67(5)(b)
(b) Solvent-spun synthetic fiber producing facilities exempted from these standards in
sub. (1) (a) (those producing less than 500 Mg (551 tons) annually) shall report to the department within 30 days whenever extruded fiber for the preceding 12 calendar months exceeds 500 Mg (551 tons).
NR 440.67 History
History: Cr.
Register, September, 1986, No. 369, eff. 10-1-86; renum. (2) (a) (intro.) and 1. to 18. to be (2) (intro.) and (a) to (r) and am. (2) (intro.), am. (3) (a), r. (5) (c),
Register, September, 1990, No. 417, eff. 10-1-90; am. (4) (b) 2. and (5) (a) 2.,
Register, July, 1993, No. 451, eff. 8-1-93;
CR 06-109: am. (1) (a), (4) (b) (intro.) and (5) (b), renum. (3) (a) to be (3) and am., r. and recr. (4) (b) 2. Register May 2008 No. 629, eff. 6-1-08. NR 440.675
NR 440.675 Volatile organic compound (VOC) emissions from the synthetic organic chemical manufacturing industry (SOCMI) air oxidation unit processes. NR 440.675(1)(1)
Applicability and designation of affected facility. NR 440.675(1)(a)(a) The provisions of this section apply to each affected facility designated in
par. (b) that produces any of the chemicals listed in
sub. (8) as a product, co-product, by-product or intermediate, except as provided in
par. (c).
NR 440.675(1)(b)
(b) The affected facility is any of the following for which construction, modification or reconstruction commenced after October 21, 1983:
NR 440.675(1)(b)1.
1. Each air oxidation reactor not discharging its vent stream into a recovery system.
NR 440.675(1)(b)2.
2. Each combination of an air oxidation reactor and the recovery system into which its vent stream is discharged.
NR 440.675(1)(b)3.
3. Each combination of 2 or more air oxidation reactors and the common recovery system into which their vent streams are discharged.
NR 440.675(1)(c)
(c) Each affected facility that has a total resource effectiveness (TRE) index value greater than 4.0 is exempt from all provisions of this section except for
subs. (3),
(5) (f),
(6) (h) and
(L).
NR 440.675 Note
Note:
The intent of these standards is to minimize the emissions of VOC through the application of best demonstrated technology (BDT). The numerical emission limits in these standards are expressed in terms of total organic compounds (TOC), measured as TOC minus methane and ethane. This emission limit reflects the performance of BDT.
