Chapter NR 230

NR 230.532 NR 230.532 Effluent limitations representing the degree of effluent reduction attainable by the application of the best practicable control technology currently available. Except as provided in 40 CFR 125.30 to 125.32, any existing point source subject to this subchapter shall achieve the following effluent limitations representing the degree of effluent reduction attainable by the application of BPT: - See PDF for table

NR 230.532 Note (1) Within the range 6.0 to 9.0

NR 230.532 History History: Cr. Register, September, 1990, No. 417, eff. 10-1-90.

NR 230.535 NR 230.535 Pretreatment standards for existing sources. Except as provided in ss. NR 211.13 and 211.14, any existing source subject to this subchapter which introduces pollutants into a POTW shall comply with ch. NR 211 and achieve the following PSES: - See PDF for table

NR 230.535 History History: Cr. Register, September, 1990, No. 417, eff. 10-1-90.

subch. LIV of ch. NR 230 Subchapter LIV — Sodium bisulfite

NR 230.54 NR 230.54 Applicability; description of the sodium bisulfite subcategory. This subchapter applies to the discharge of pollutants to waters of the state and the introduction of pollutants into POTWs from the production of sodium bisulfite.

NR 230.54 History History: Cr. Register, September, 1990, No. 417, eff. 10-1-90.

NR 230.542 NR 230.542 Effluent limitations representing the degree of effluent reduction attainable by the application of the best practicable control technology currently available. Except as provided in 40 CFR 125.30 to 125.32, any existing point source subject to this subchapter shall achieve the following effluent limitations representing the degree of effluent reduction attainable by application of BPT: - See PDF for table

NR 230.542 Note (1) Within the range of 6.0 to 9.0

NR 230.542 History History: Cr. Register, September, 1990, No. 417, eff. 10-1-90.

NR 230.543 NR 230.543 Effluent limitations representing the degree of effluent reduction attainable by the application of the best available technology economically achievable. Except as provided in 40 CFR 125.30 to 125.32, any existing point source subject to this subchapter shall achieve the limitations set forth in s. NR 230.542 for COD, chromium, and zinc.

NR 230.543 History History: Cr. Register, September, 1990, No. 417, eff. 10-1-90.

NR 230.544 NR 230.544 New source performance standards. Any new source subject to this subchapter shall achieve the limitations set forth in s. NR 230.542.

NR 230.544 History History: Cr. Register, September, 1990, No. 417, eff. 10-1-90.

NR 230.546 NR 230.546 Pretreatment standards for new sources. Except as provided in s. NR 211.13, any new source subject to this subchapter which introduces pollutants into a POTW shall comply with ch. NR 211 and achieve the following PSNS: - See PDF for table

NR 230.546 Note (1) When a POTW finds that mass limitations are necessary, the PSES shall be the limitations set forth in s. NR 230.542 for chromium.

NR 230.546 History History: Cr. Register, September, 1990, No. 417, eff. 10-1-90.

NR 230.547 NR 230.547 Effluent limitations representing the degree of effluent reduction attainable by the application of the best conventional pollutant control technology. Except as provided in 40 CFR 125.30 to 125.32, any existing point source subject to this subchapter shall achieve the effluent limitations set forth in s. NR 230.542 for TSS and pH.

NR 230.547 History History: Cr. Register, September, 1990, No. 417, eff. 10-1-90.

subch. LV of ch. NR 230 Subchapter LV — Sodium fluoride

NR 230.55 NR 230.55 Applicability; description of the sodium fluoride subcategory. This subchapter applies to the discharge of pollutants to waters of the state and the introduction of pollutants into POTWs from the production of sodium fluoride by the anhydrous neutralization process and by the silico fluoride process.

NR 230.55 History History: Cr. Register, September, 1990, No. 417, eff. 10-1-90.

NR 230.551 NR 230.551 Specialized definitions. The following definitions apply to the terms used in this subchapter:

NR 230.551(1) (1) “Contaminated nonprocess wastewater" means any water which, during manufacturing or processing, comes into incidental contact with any raw material, intermediate product, finished product, byproduct, or waste product.

NR 230.551(2) (2) “Incidental contact" means contact resulting from:

NR 230.551(2)(a) (a) Rainfall runoff;

NR 230.551(2)(b) (b) Accidental spills;

NR 230.551(2)(c) (c) Accidental leaks which are caused by failure of process equipment and which are repaired within the shortest reasonable time not to exceed 24 hours after discovery; and

NR 230.551(2)(d) (d) Discharges from safety showers and related personal safety equipment.

NR 230.551(3) (3) “Process wastewater" means any water which, during manufacturing or processing, comes into contact with or results from the production or use of any raw material, intermediate product, finished product, byproduct, or waste product, except for contaminated nonprocess wastewater.

NR 230.551(4) (4) “Process wastewater pollutants" means pollutants present in the process wastewater.

NR 230.551 History History: Cr. Register, September, 1990, No. 417, eff. 10-1-90.

NR 230.5515 NR 230.5515 Regulation of contaminated nonprocess wastewater. Contaminated nonprocess wastewater shall be regulated as process wastewater unless all reasonable measures have been taken to prevent, reduce, and control incidental contact and to mitigate the effects of incidental contact after it has occurred.

NR 230.5515 History History: Cr. Register, September, 1990, No. 417, eff. 10-1-90.

NR 230.552 NR 230.552 Effluent limitations representing the degree of effluent reduction attainable by the application of the best practicable control technology currently available. Except as provided in 40 CFR 125.30 to 125.32, any existing point source subject to this subchapter may not discharge wastewater pollutants to waters of the state.

NR 230.552 History History: Cr. Register, September, 1990, No. 417, eff. 10-1-90.

NR 230.555 NR 230.555 Pretreatment standards for existing sources. Except as provided in ss. NR 211.13 and 211.14, any existing source subject to this subchapter which introduces pollutants into a POTW shall comply with ch. NR 211 and achieve the following PSES: - See PDF for table

NR 230.555 History History: Cr. Register, September, 1990, No. 417, eff. 10-1-90.

NR 230.556 NR 230.556 Pretreatment standards for new sources. Except as provided in s. NR 211.13, any new source subject to this subchapter which introduces pollutants into a POTW shall comply with ch. NR 211 and may not discharge process wastewater pollutants into a POTW.

NR 230.556 History History: Cr. Register, September, 1990, No. 417, eff. 10-1-90.

subch. LX of ch. NR 230 Subchapter LX — Stannic oxide

NR 230.60 NR 230.60 Applicability; description of the stannic oxide subcategory. This subchapter applies to the discharge of pollutants to waters of the state and the introduction of pollutants into POTWs from the production of stannic oxide by the reaction of tin metal with air or oxygen.

NR 230.60 History History: Cr. Register, September, 1990, No. 417, eff. 10-1-90.

NR 230.601 NR 230.601 Specialized definitions. The following definitions apply to the terms used in this subchapter:

NR 230.601(1) (1) “Contaminated nonprocess wastewater" means any water which, during manufacturing or processing, comes into incidental contact with any raw material, intermediate product, finished product, byproduct or waste product.

NR 230.601(2) (2) “Incidental contact" means contact resulting from:

NR 230.601(2)(a) (a) Rainfall runoff;

NR 230.601(2)(b) (b) Accidental spills;

NR 230.601(2)(c) (c) Accidental leaks which are caused by failure of process equipment and which are repaired within the shortest reasonable time not to exceed 24 hours after discovery; and

NR 230.601(2)(d) (d) Discharges from safety showers and related personal safety equipment.

NR 230.601(3) (3) “Process wastewater" means any water which, during manufacturing or processing, comes into contact with or results from the production or use of any raw material, intermediate product, finished product, byproduct, or waste product, except for contaminated nonprocess wastewater.

NR 230.601(4) (4) “Process wastewater pollutants" means pollutants present in the process wastewater.

NR 230.601 History History: Cr. Register, September, 1990, No. 417, eff. 10-1-90.

NR 230.6015 NR 230.6015 Regulation of contaminated nonprocess wastewater. Contaminated nonprocess wastewater shall be regulated as process wastewater unless all reasonable measures have been taken to prevent, reduce, and control incidental contact and to mitigate the effects of incidental contact after it has occurred.

NR 230.6015 History History: Cr. Register, September, 1990, No. 417, eff. 10-1-90.

NR 230.602 NR 230.602 Effluent limitations representing the degree of effluent reduction attainable by the application of the best practicable control technology currently available. Except as provided in 40 CFR 125.30 to 125.32, any existing point source subject to this subchapter may not discharge wastewater pollutants to waters of the state.

NR 230.602 History History: Cr. Register, September, 1990, No. 417, eff. 10-1-90.

NR 230.606 NR 230.606 Pretreatment standards for new sources. Except as provided in s. NR 211.13, any new source subject to this subchapter which introduces pollutants into a POTW shall comply with ch. NR 211 and may not discharge process wastewater pollutants into a POTW.

NR 230.606 History History: Cr. Register, September, 1990, No. 417, eff. 10-1-90.

subch. LXIII of ch. NR 230 Subchapter LXIII — Zinc sulfate

NR 230.63 NR 230.63 Applicability; description of the zinc sulfate subcategory. This subchapter applies to the discharge of pollutants to waters of the state and the introduction of pollutants into POTWs from the production of zinc sulfate.

NR 230.63 History History: Cr. Register, September, 1990, No. 417, eff. 10-1-90.

NR 230.631 NR 230.631 Specialized definitions. The following definitions apply to the terms used in this subchapter:

NR 230.631(1) (1) “Contaminated nonprocess wastewater" means any water which, during manufacturing or processing, comes into incidental contact with any raw material, intermediate product, finished product, byproduct, or waste product.

NR 230.631(2) (2) “Incidental contact" means contact resulting from:

NR 230.631(2)(a) (a) Rainfall runoff;

NR 230.631(2)(b) (b) Accidental spills;

NR 230.631(2)(c) (c) Accidental leaks which are caused by failure of process equipment and which are repaired within the shortest reasonable time not to exceed 24 hours after discovery; and

NR 230.631(2)(d) (d) Discharges from safety showers and related personal safety equipment.

NR 230.631(3) (3) “Process wastewater" means any water which, during manufacturing or processing, comes into contact with or results from the production or use of any raw material, intermediate product, finished product, byproduct, or waste product, except for contaminated nonprocess wastewater.

NR 230.631(4) (4) “Process wastewater pollutants" means pollutants present in the process wastewater.

NR 230.631 History History: Cr. Register, September, 1990, No. 417, eff. 10-1-90.

NR 230.6315 NR 230.6315 Regulation of contaminated nonprocess wastewater. Contaminated nonprocess wastewater shall be regulated as process wastewater unless all reasonable measures have been taken to prevent, reduce, and control incidental contact and to mitigate the effects of incidental contact after it has occurred.

NR 230.6315 History History: Cr. Register, September, 1990, No. 417, eff. 10-1-90.

NR 230.632 NR 230.632 Effluent limitations representing the degree of effluent reduction attainable by the application of the best practicable control technology currently available. Except as provided in 40 CFR 125.30 to 125.32, any existing point source subject to this subchapter may not discharge wastewater pollutants to waters of the state.

NR 230.632 History History: Cr. Register, September, 1990, No. 417, eff. 10-1-90.

NR 230.636 NR 230.636 Pretreatment standards for new sources. Except as provided in s. NR 211.13, any new source subject to this subchapter which introduces pollutants into a POTW shall comply with ch. NR 211 and may not discharge process wastewater pollutants into a POTW.

NR 230.636 History History: Cr. Register, September, 1990, No. 417, eff. 10-1-90.

subch. LXIV of ch. NR 230 Subchapter LXIV — Cadmium pigments and salts

NR 230.64 NR 230.64 Applicability; description of the cadmium pigments and salts subcategory. This subchapter applies to the discharge of pollutants to waters of the state and the introduction of pollutants into POTWs from the production of cadmium pigments and salts, such as cadmium chloride, cadmium nitrate, and cadmium sulfate.

NR 230.64 History History: Cr. Register, September, 1990, No. 417, eff. 10-1-90.

NR 230.642 NR 230.642 Effluent limitations representing the degree of effluent reduction attainable by the application of the best practicable control technology currently available. Except as provided in 40 CFR 125.30 to 125.32, any existing point source subject to this subchapter shall achieve the following effluent limitations representing the degree of effluent reduction attainable by application of BPT: - See PDF for table

NR 230.642 Note (1) Within the range of 6.0 to 9.0 - See PDF for table

NR 230.642 Note (1) Within the range of 6.0 to 9.0

NR 230.642 History History: Cr. Register, September, 1990, No. 417, eff. 10-1-90.

NR 230.643 NR 230.643 Effluent limitations representing the degree of effluent reduction attainable by the application of the best available technology economically achievable. Except as provided in 40 CFR 125.30 to 125.32, any existing point source subject to this subchapter shall achieve the limitations set forth in s. NR 230.642 for cadmium, selenium, and zinc.

NR 230.643 History History: Cr. Register, September, 1990, No. 417, eff. 10-1-90.

NR 230.644 NR 230.644 New source performance standards. Any new source subject to this subchapter shall achieve the limitations set forth in s. NR 230.642.