NR 214.17(4)(d)7.
7. The total pounds of chloride applied shall be limited to 170 pounds per acre per year or 340 pounds per acre per 2 year period.
NR 214.17(4)(d)8.
8. The total pounds of sodium applied may be limited to prevent alteration of soil properties or groundwater contamination.
NR 214.17(4)(d)9.
9. The total pounds of nitrogen applied per acre per year shall be limited to the nitrogen needs of the cover crop minus any other nitrogen, including fertilizer or manure, added to the landspreading site. Nitrogen applied can be calculated on the basis of plant available nitrogen, as long as the release of nitrogen from the organic material is credited to future years.
NR 214.17(4)(d)10.
10. For whey, not including whey by-products, where the nitrogen content has not been determined through sampling and analysis, the nitrogen application rate shall be limited by limiting the yearly hydraulic application rate for a site to 27,150 gallons per acre (1 inch) the first year, 20,360 gallons per acre (
3/
4 inch) the second year, and 13,600 gallons per acre (
1/
2inch) the third and succeeding years.
NR 214.17(4)(e)1.1. The volume of by-product solids landspread may not alter the characteristics or structure of the soil such that the crop is adversely affected or erosion or permeability problems occur.
NR 214.17(4)(e)2.
2. The total quantity of by-product solids applied to the soil shall be within acceptable agricultural practices taking into account the carbon to nitrogen ratio, total nitrogen and the moisture content of the by-product solid.
NR 214.17(4)(e)3.
3. The volume of by-product solids landspread shall be limited to prevent surface runoff of solids or leachate, leaching of contaminants to groundwater and objectionable odors.
NR 214.17(4)(e)4.
4. The total pounds of chloride applied shall be limited to 170 pounds per acre per year or to 340 pounds per acre per 2 year period.
NR 214.17(4)(e)5.
5. The total pounds of sodium applied may be limited to prevent alteration of soil properties or groundwater contamination.
NR 214.17(4)(e)6.
6. The total pounds of nitrogen applied per acre per year shall be limited to the nitrogen needs of the cover crop minus any other nitrogen, including fertilizer or manure, added to the landspreading site. Nitrogen applied can be calculated on the basis of plant available nitrogen, as long as the release of nitrogen from the organic material is credited to future years.
NR 214.17(4)(e)7.
7. The by-product solids shall be plowed, disced, injected or otherwise incorporated into the surface soil layer as specified in the WPDES permit or approved management plan.
NR 214.17(4)(e)8.
8. If it is necessary to stockpile solids in the field, the piles shall be spread within 72 hours or less as specified in the WPDES permit or management plan.
NR 214.17(5)(a)(a) The discharge to landspreading systems shall be monitored for total daily discharge volume.
NR 214.17(5)(b)
(b) The department may require in a WPDES permit that the discharge to the system be monitored for BOD
5, total suspended solids, forms of nitrogen, chloride, metals or any other pollutant that may be present. The department shall select the pollutants to be monitored and the required frequency of monitoring on a case-by-case basis by considering the potential public health impacts, probable environmental impact, soil and geologic conditions, past operating performance, concentrations and characteristics of pollutants in the discharge and other relevant information.
NR 214.17(5)(c)
(c) The department may require electronic or paper submittal of discharge monitoring reports and land application forms.
NR 214.17(6)(a)
(a) Vehicles used for transporting or landspreading the waste shall be maintained to prevent spillage or leakage.
NR 214.17(6)(b)
(b) The landspreading vehicle shall be moving forward at all times of application unless it is equipped with a high pressure spray nozzle which evenly distributes the waste over the land.
NR 214.17(6)(c)
(c) Management plan. The department shall require each landspreading system owner or operator to submit a management plan for optimizing system performance and demonstrating compliance with the requirements of this chapter. Following approval by the department, the treatment system shall be operated in conformance with the management plan. If the facility wishes to operate differently than specified in the approved plan, a written request shall be submitted to the department for approval to amend the management plan. The plan shall specify information on pretreatment processes, site identification on plat and soil maps, aerial photographs, if available, description of all site limitations, vegetative cover management and removal, availability of storage, type of transporting and spreading vehicle, load and rest schedules, monitoring procedures, contingency plans for periods of adverse weather or odor or nuisance abatement and any other pertinent information.
NR 214.17(7)
(7) Soils investigation and groundwater monitoring requirements. Soil investigation and groundwater monitoring requirements are specified in ss.
NR 214.20 and
214.21.
NR 214.17 History
History: Cr.
Register, June, 1990, No. 414, eff. 7-1-90;
CR 09-123: cr. (5) (c)
Register July 2010 No. 655, eff. 8-1-10.
NR 214.18
NR 214.18
Sludge spreading systems. NR 214.18(1)(1)
Applicability. Only sludges which have been exempted from regulation under ch.
NR 518 and have been shown to have beneficial properties as a soil conditioner or fertilizer and not have detrimental effects on the soil, crops or groundwater may be spread on the land. A WPDES permit is required for the spreading of sludge on land.
NR 214.18(2)(a)
(a) All sites shall be approved by the department prior to sludge being spread.
NR 214.18(2)(b)
(b) Sludge may not be spread within 500 feet of any residence, except that this distance may be reduced to 200 feet if the sludge is incorporated with the soil and any affected owners and occupants give their written consent for the reduced separation distance.
NR 214.18(2)(c)
(c) Sludge may not be spread within 1000 feet of a well serving a community public water supply system or within 250 feet of any other potable water supply well.
NR 214.18(2)(d)
(d) Sludge may not be surface spread within 200 feet from any surface water course, dry run or wetlands, except that if a vegetative buffer strip is maintained between the site and the surface water, the department may approve a reduced separation distance to 100 feet. If the sludge is incorporated in the soil, the separation distance from any surface water may be reduced to a minimum of 50 feet.
NR 214.18(2)(e)
(e) Sludge may not be spread on wetlands or on areas subject to flooding or ponding.
NR 214.18(2)(f)
(f) Sludge spreading sites shall be limited to a slope of 12% or less when the soil temperatures are above freezing. When the ground is frozen or snow covered, the landspreading shall be restricted to sites with slopes of 2% or less. Sites with slopes of 2-6% may be approved for winter time spreading on a case-by-case basis.
NR 214.18(2)(g)
(g) Sludge spreading sites shall have at least 36 inches of separation between the ground surface and bedrock or groundwater. However, the department may allow a reduced separation distance to a minimum of 18 inches on a case-by-case basis provided the rate of application is reduced.
NR 214.18(3)(a)
(a) Vehicles used for spreading shall be equipped with a distribution system capable of spreading the sludge evenly over the site.
NR 214.18(3)(b)
(b) Any system used for the storage or stacking of sludge prior to spreading shall be designed and constructed in accordance with ch.
NR 213, or other design criteria as approved in the sludge management plan. Plans and specifications shall be submitted to the department for approval of such storage or stacking systems.
NR 214.18(3)(c)
(c) Storage or stacking systems shall be sited and operated to minimize odors or other public nuisance conditions.
NR 214.18(4)(a)
(a) The discharge to a sludge spreading site may not exceed the hydraulic, organic, nitrogen, chloride or other limitations specified in a WPDES permit or plans developed pursuant to a permit requirement. In determining discharge limitations, the department shall consider past operating performance, the ability of the soils to treat the pollutants in the discharge, nutrient uptake of the cover crops, hydrogeologic characteristics of the site such as permeability and infiltration rates, and other relevant information.
NR 214.18(4)(b)
(b) The sludge application rate shall be limited so that any parameter that may impact groundwater quality is restricted to minimize the concentration of the substance in the groundwater to the extent technically and economically feasible and to prevent exceedence of the preventive action limit in the groundwater.
NR 214.18(4)(c)
(c) In order to prevent surface runoff and leaching and to control objectionable odors, the department may require liquid sludge to be incorporated into the soil surface within a time period specified in the WPDES permit. Cake sludge shall be incorporated in the soil in accordance with the time period specified in the sludge spreading management plan.
NR 214.18(4)(d)
(d) The total amount of any nutrient applied per year may not exceed the nutrient needs of the crop to be grown minus available nutrients in the soil or applied as fertilizer.
NR 214.18(4)(e)
(e) The pH of the sludge and soil mixture shall be 6.5 or higher at the time that the sludge is spread. If the concentration of cadmium in the sludge is 2 mg/kg (dry weight) or less, the soil pH may be less than 6.5.
NR 214.18(4)(f)
(f) No more than 0.45 pounds per acre of cadmium may be spread annually on land used for production of food chain crops.
NR 214.18(4)(g)
(g) The cumulative amount of cadmium, copper, lead, nickel and zinc spread on any site may not exceed the levels listed in Table 4.
-
See PDF for table 
NR 214.18(4)(h)
(h) Sludge containing concentrations of PCBs equal to or greater than 10 mg/kg (dry weight) shall be incorporated into the soil when applied to land used for producing animal feed, including pasture crops for animals raised for the purpose of producing milk. The department may allow surface application of the sludge if it is assured that the PCB content is less than 0.2 mg/kg (actual weight) in animal feed or less than 1.5 mg/kg (fat basis) in milk from animals consuming the feed.
NR 214.18(4)(i)
(i) The department may limit or prohibit the land application of sludges containing additional pollutants such as, but not limited to phenolics, pesticides and bioaccumulative organics. Any such limit or prohibition shall be based on waste characteristics, soil cation exchange capacity, type of crop grown and other relevant factors.
NR 214.18(5)(a)(a) The discharge shall be monitored for total daily discharge volume.
NR 214.18(5)(b)
(b) The department may require in a WPDES permit that the sludge spreading discharge be monitored for total suspended solids, forms of nitrogen, chloride, metals or any other pollutant that may be present. The department shall select the pollutants to be monitored and the required frequency of monitoring on a case-by-case basis by considering the potential public health impacts, probable environmental impact, soil and geologic conditions, past operating performance, concentrations and characteristics of pollutants in the discharge and other relevant information.
NR 214.18(5)(c)
(c) The department may require the submittal of monitoring reports to include the following information for each site utilized during the reporting period:
NR 214.18(5)(c)1.
1. The amount of sludge applied in tons per acre on a dry weight basis.
NR 214.18(5)(c)2.
2. The amount of nitrogen applied in pounds per acre on a dry weight basis.
NR 214.18(5)(c)3.
3. The amount of each metal applied in pounds per acre on a dry weight basis.
NR 214.18(5)(c)4.
4. Other site monitoring information as specified in the sludge management plan or WPDES permit.
NR 214.18(5)(c)5.
5. A description of any adverse environmental, health or social effects that occurred due to sludge application during the preceding reporting period.
NR 214.18(5)(d)
(d) The department may require electronic or paper submittal of discharge monitoring reports and land application forms.
NR 214.18(6)(a)
(a) Spillage or leakage from vehicles used for transporting or spreading sludge shall be prevented.
NR 214.18(6)(b)
(b) The vehicle shall be moving forward at all times of application unless it is equipped with a high pressure spray nozzle which evenly distributes the sludge over the land.
NR 214.18(6)(c)
(c) Management plan. The department shall require each sludge spreading system owner or operator to submit a management plan for optimizing system performance and demonstrating compliance with the requirements of this chapter. Following approval by the department, the system shall be operated in conformance with the management plan. If the facility wishes to operate differently than specified in the approved plan, a written request shall be submitted to the department for approval to amend the management plan. The plan shall specify information on: sludge volumes and characteristics, beneficial or nondetrimental fertilizer or soil conditioner properties, production and pretreatment processes, description of all site limitations, vegetative cover control and removal, availability of storage, type of transportation and spreading vehicle, sludge application rates, load and rest schedules, contingency plans for periods of adverse weather, odor and nuisance abatement or any other pertinent information.
NR 214.18(7)
(7) Soil investigation and groundwater monitoring requirements. Soil investigation and groundwater monitoring requirements are specified in ss.
NR 214.20 and
214.21.
NR 214.18 History
History: Cr.
Register, June, 1990, No. 414, eff. 7-1-90;
CR 09-123: cr. (5) (d)
Register July 2010 No. 655, eff. 8-1-10.
NR 214.20
NR 214.20
Soil investigation requirements. NR 214.20(1)(1)
Applicability. This section is applicable to all new, expanded or modified land treatment systems receiving liquid wastes, by-product solids and sludges from industrial facilities for which a plan approval under s.
281.41, Stats., and ch.
NR 108 or a WPDES discharge permit under ch.
283, Stats., is required. It is also applicable to those existing dischargers which need to demonstrate according to s.
NR 214.06 (1) that their land treatment system complies with groundwater protection requirements although the system does not meet each specific design standard.
NR 214.20(2)
(2) Professional qualifications. The department shall accept soil test pit evaluations, soil classifications and soil boring logs performed by a qualified soil scientist, engineer or other qualified individual. Qualifications shall include a degree from an accredited institution of higher education or field experience in soil investigation, interpretation and classification.
NR 214.20(3)
(3) Technical procedures. All technical procedures used to investigate a wastewater disposal facility shall be the current standard procedures as specified by the American society for testing and materials, United States geologic survey, standard methods for the examination of water and wastewater, or other equivalent or appropriate methods approved by the department. Test procedures used shall be specified. Any deviation from a standard method shall be explained in detail with reasons provided.
NR 214.20(4)
(4) Soil evaluations for landspreading and sludge spreading systems. The following soil related information shall be submitted for sludge spreading systems or landspreading systems for liquid waste or organic by-product solids:
NR 214.20(4)(a)
(a) Individual treatment site locations identified on topographic maps, plat maps or aerial photographs,
NR 214.20(4)(b)
(b) Relevant, existing soil survey information such as that assembled by the U.S. department of agriculture, soil conservation service including the soil names, percent slope, relative permeability, available water capacity, organic matter content and current land use,
NR 214.20(4)(c)
(c) A detailed soils map displaying the location of the various soils on the site at a scale of not more than 2,000 feet to the inch,
NR 214.20(4)(d)
(d) Laboratory determined or estimated soil cation exchange capacity,
NR 214.20(4)(e)
(e) Agronomic soil nutrient testing results for making fertilizer and liming recommendations for cover crop growth using procedures such as those employed by the university of Wisconsin - cooperative extension program,
NR 214.20(4)(f)
(f) Additional soil related information that may be required by the department on a case-by-case basis.
NR 214.20(5)
(5) Treatment systems where groundwater monitoring wells are not required. For absorption pond, ridge and furrow, spray irrigation, overland flow and subsurface absorption systems where groundwater monitoring wells are not required, or for those sites which are being investigated for potential future use as such systems, the soils evaluation shall contain the following information and investigation, at a minimum:
NR 214.20(5)(a)
(a) The location, soil survey, soil cation exchange capacity and soil nutrient content information as specified for landspreading systems in sub.
(4).
NR 214.20(5)(b)
(b) A sufficient number of soil test pits shall be excavated to adequately define the soil conditions found on the site.
NR 214.20(5)(b)1.
1. Prior to soil test pit construction, the treatment site owner or operator and the department shall agree on the number and location of test pits to be excavated dependent upon the size of the land treatment site and uniformity of soils and geology.
NR 214.20(5)(b)2.
2. The soil test pits shall be large enough to allow visual inspection and documentation of soil layers and shall be excavated to a depth of 5 feet below the final base grade of the system. The U.S. occupational health and safety administration requires that test pits with more than 5 feet of standing wall shall not be entered unless provision is made to prevent caving of the walls.
NR 214.20(5)(b)3.
3. The department shall be notified at least 24 hours prior to excavation of the soil test pits to allow inspection by department personnel.
NR 214.20(5)(c)
(c) Soil samples from the test pits shall be collected and analyzed at each significant change in soil characteristics or lithology for the following:
NR 214.20(5)(c)1.
1. Soil textural classification in accordance with the unified soil classification system as specified in ASTM standard D-2487-85.
NR 214.20(5)(c)2.
2. Particle size analysis performed in accordance with ASTM D422-72 to determine particle size distribution. With department approval, soil samples may be composited, or the particle size determined by a sieve analysis to reduce repetitive testing of similar soil samples.
NR 214.20(5)(c)3.
3. The soil moisture holding capacity by direct measurement or as specified through reference to literature values for different soil textures.
NR 214.20(5)(d)
(d) Following soil sample collection, the test pits shall be deepened to the extent practical with a backhoe to check for bedrock, the water table or for soil layers that would restrict the downward movement of water. This shall be visual check from the land surface, unless the test pits are protected from caving in accordance with U.S. occupational safety and health administration requirements. All soil test pits shall be refilled with excavated material following deepening for the bedrock, water table and impervious layer check.
NR 214.20(6)
(6) Treatment systems with required groundwater monitoring. For land treatment systems where groundwater monitoring wells are required, the soils evaluation shall contain the following information and investigation, at a minimum:
NR 214.20(6)(a)
(a) A preliminary site investigation report shall be assembled that contains the site location, soil survey, soil cation exchange capacity and soil nutrient content information as specified for landspreading systems in sub.
(4). Also, a limited number of test pits may be constructed to provide preliminary soils information, such as that specified in sub.
(5).
