This is the preview version of the Wisconsin State Legislature site.
Please see http://docs.legis.wisconsin.gov for the production version.
subch. XXXIV of ch. NR 230 Subchapter XXXIV - Chrome pigments
NR 230.34 NR 230.34Applicability; description of the chrome pigments subcategory. This subchapter applies to the discharge of pollutants to waters of the state and the introduction of pollutants into POTWs from the production of chrome yellow, chrome orange, molybdate chrome orange, anhydrous and hydrous chromium oxide, chrome green, and zinc yellow.
NR 230.34 History History: Cr. Register, September, 1990, No. 417, eff. 10-1-90.
NR 230.342 NR 230.342Effluent limitations representing the degree of effluent reduction attainable by the application of the best practicable control technology currently available. Except as provided in 40 CFR 125.30 to 125.32, any existing point source subject to this subchapter shall achieve the following effluent limitations representing the degree of effluent reduction attainable by application of BPT: - See PDF for table PDF
NR 230.342 Note (1) Within the range of 6.0 to 9.0
NR 230.342 History History: Cr. Register, September, 1990, No. 417, eff. 10-1-90.
NR 230.343 NR 230.343Effluent limitations representing the degree of effluent reduction attainable by the application of the best available technology economically achievable. Except as provided in 40 CFR 125.30 to 125.32, any existing point source subject to this subchapter shall achieve limitations set forth in s. NR 230.342 for chromium, lead, and zinc.
NR 230.343 History History: Cr. Register, September, 1990, No. 417, eff. 10-1-90.
NR 230.344 NR 230.344New source performance standards. Any new source subject to this subchapter shall achieve the limitations set forth in s. NR 230.342.
NR 230.344 History History: Cr. Register, September, 1990, No. 417, eff. 10-1-90.
NR 230.345 NR 230.345Pretreatment standards for existing sources.
NR 230.345(1)(1) Except as provided in ss. NR 211.13 and 211.14 and sub. (2), any existing source subject to this subchapter which introduces pollutants into a POTW shall comply with ch. NR 211 and achieve the following PSES: - See PDF for table PDF
NR 230.345 Note (1) When a POTW finds that mass limitations are necessary, the PSES shall be the limitations set forth in s. NR 230.342 for chromium, lead, and zinc.
NR 230.345(2) (2) Existing sources which annually introduce less than 210,000 cubic meters (55 million gallons) of chrome pigments process wastewater into a POTW shall comply with ch. NR 211.
NR 230.345 History History: Cr. Register, September, 1990, No. 417, eff. 10-1-90.
NR 230.346 NR 230.346Pretreatment standards for new sources. Except as provided in s. NR 211.13, any new source subject to this subchapter which introduces pollutants into a POTW shall comply with ch. NR 211 and achieve the standards set forth in s. NR 230.345.
NR 230.346 History History: Cr. Register, September, 1990, No. 417, eff. 10-1-90.
NR 230.347 NR 230.347Effluent limitations representing the degree of effluent reduction attainable by the application of the best conventional pollutant control technology. Except as provided in 40 CFR 125.30 to 125.32, any existing point source subject to this subchapter shall achieve the effluent limitations set forth in s. NR 230.342 for TSS and pH.
NR 230.347 History History: Cr. Register, September, 1990, No. 417, eff. 10-1-90.
subch. XXXV of ch. NR 230 Subchapter XXXV — Chromic acid
NR 230.35 NR 230.35Applicability; description of the chromic acid subcategory. This subchapter applies to the discharge of pollutants to waters of the state and the introduction of pollutants into POTWs from the production of chromic acid by facilities which also manufacture sodium dichromate.
NR 230.35 History History: Cr. Register, September, 1990, No. 417, eff. 10-1-90.
NR 230.352 NR 230.352Effluent limitations representing the degree of effluent reduction attainable by the application of the best practicable control technology currently available. Except as provided in 40 CFR 125.30 to 125.32, any existing point source subject to this subchapter shall achieve the limitations set forth in s. NR 230.172.
NR 230.352 History History: Cr. Register, September, 1990, No. 417, eff. 10-1-90.
NR 230.356 NR 230.356Pretreatment standards for new sources. Except as provided in s. NR 211.13, any new source subject to this subchapter which introduces pollutants into a POTW shall comply with ch. NR 211 and achieve the standards set forth in s. NR 230.172.
NR 230.356 History History: Cr. Register, September, 1990, No. 417, eff. 10-1-90.
subch. XXXVI of ch. NR 230 Subchapter XXXVI — Copper salts
NR 230.36 NR 230.36Applicability; description of the copper salts subcategory. This subchapter applies to the discharge of pollutants to waters of the state and the introduction of pollutants into POTWs from the production of copper salts, such as copper sulfate, copper chloride, copper iodide, copper nitrate, and copper carbonate.
NR 230.36 History History: Cr. Register, September, 1990, No. 417, eff. 10-1-90.
NR 230.362 NR 230.362Effluent limitations representing the degree of effluent reduction attainable by the application of the best practicable control technology currently available. Except as provided in 40 CFR 125.30 to 125.32, any existing point source subject to this subchapter shall achieve the following effluent limitations representing the degree of effluent reduction attainable by application of BPT: - See PDF for table PDF
NR 230.362 Note (1) Within the range of 6.0 to 9.0 - See PDF for table PDF
NR 230.362 Note (1) Within the range of 6.0 to 9.0
NR 230.362 History History: Cr. Register, September, 1990, No. 417, eff. 10-1-90.
NR 230.363 NR 230.363Effluent limitations representing the degree of effluent reduction attainable by the application of the best available technology economically achievable. Except as provided in 40 CFR 125.30 to 125.32, any existing point source subject to this subchapter shall achieve limitations set forth in s. NR 230.362 for copper, nickel, and selenium.
NR 230.363 History History: Cr. Register, September, 1990, No. 417, eff. 10-1-90.
NR 230.364 NR 230.364New source performance standards. Any new [existing] source subject to this subchapter shall achieve the limitations set forth in s. NR 230.362.
NR 230.364 History History: Cr. Register, September, 1990, No. 417, eff. 10-1-90.
NR 230.365 NR 230.365Pretreatment standards for existing sources. Except as provided in ss. NR 211.13 and 211.14, any new [existing] source subject to the copper salts subchapter which introduces pollutants into a POTW shall comply with ch. NR 211 and achieve the following PSES: - See PDF for table PDF
NR 230.365 Note (1) When a POTW finds that mass limitations are necessary, the PSES shall be the limitations set forth in s. NR 230.362 for copper, nickel, and selenium.
NR 230.365 History History: Cr. Register, September, 1990, No. 417, eff. 10-1-90.
NR 230.366 NR 230.366Pretreatment standards for new sources. Except as provided in s. NR 211.13, any new source subject to this subchapter which introduces pollutants into a POTW shall comply with ch. NR 211 and achieve the standards set forth in s. NR 230.365.
NR 230.366 History History: Cr. Register, September, 1990, No. 417, eff. 10-1-90.
NR 230.367 NR 230.367Effluent limitations representing the degree of effluent reduction attainable by the application of the best conventional pollutant control technology. Except as provided in 40 CFR 125.30 to 125.32, any existing point source subject to this subchapter shall achieve the effluent limitations set forth in s. NR 230.362 for TSS and pH.
NR 230.367 History History: Cr. Register, September, 1990, No. 417, eff. 10-1-90.
subch. XXXVIII of ch. NR 230 Subchapter XXXVIII — Ferric chloride
NR 230.38 NR 230.38Applicability; description of the ferric chloride subcategory. This subchapter applies to the discharge of pollutants to waters of the state and the introduction of pollutants into POTWs from the production of ferric chloride from pickle liquor.
NR 230.38 History History: Cr. Register, September, 1990, No. 417, eff. 10-1-90.
NR 230.381 NR 230.381Specialized definitions. The following definitions apply to the terms used in this subchapter:
NR 230.381(1) (1) “Contaminated nonprocess wastewater" means any water which, during manufacturing or processing, comes into incidental contact with any raw material, intermediate product, finished product, byproduct, or waste product.
NR 230.381(2) (2) “Incidental contact" means contact resulting from:
NR 230.381(2)(a) (a) Rainfall runoff;
NR 230.381(2)(b) (b) Accidental spills;
NR 230.381(2)(c) (c) Accidental leaks which are caused by failure of process equipment and which are repaired within the shortest reasonable time not to exceed 24 hours after discovery; and
NR 230.381(2)(d) (d) Discharges from safety showers and related personal safety equipment.
NR 230.381(3) (3) “Process wastewater" means any water which, during manufacturing or processing, comes into contact with or results from the production or use of any raw material, intermediate product, finished product, byproduct, or waste product, except for contaminated nonprocess wastewater.
NR 230.381(4) (4) “Process wastewater pollutants" means pollutants present in the process wastewater.
NR 230.381 History History: Cr. Register, September, 1990, No. 417, eff. 10-1-90.
NR 230.3815 NR 230.3815Regulation of contaminated nonprocess wastewater. Contaminated nonprocess wastewater shall be regulated as process wastewater unless all reasonable measures have been taken to prevent, reduce, and control incidental contact and to mitigate the effects of incidental contact after it has occurred.
NR 230.3815 History History: Cr. Register, September, 1990, No. 417, eff. 10-1-90.
NR 230.382 NR 230.382Effluent limitations representing the degree of effluent reduction attainable by the application of the best practicable control technology currently available. Except as provided in 40 CFR 125.30 to 125.32, any existing point source subject to this subchapter may not discharge process wastewater pollutants into waters of the state.
NR 230.382 History History: Cr. Register, September, 1990, No. 417, eff. 10-1-90.
NR 230.385 NR 230.385Pretreatment standards for existing sources. Except as provided in ss. NR 211.13 and 211.14, any existing source subject to this subchapter which introduces pollutants into a POTW shall comply with ch. NR 211 and achieve the following PSES: - See PDF for table PDF
NR 230.385 History History: Cr. Register, September, 1990, No. 417, eff. 10-1-90.
NR 230.386 NR 230.386Pretreatment standards for new sources. Except as provided in s. NR 211.13, any new source subject to this subchapter which introduces pollutants into a POTW shall comply with ch. NR 211 and may not discharge process wastewater pollutants into a POTW.
NR 230.386 History History: Cr. Register, September, 1990, No. 417, eff. 10-1-90.
subch. XL of ch. NR 230 Subchapter XL — Fluorine
NR 230.40 NR 230.40Applicability; description of the fluorine subcategory. This subchapter applies to the discharge of pollutants to waters of the state and the introduction of pollutants into POTWs from the production of fluorine by the liquid hydrofluoric acid electrolysis process.
NR 230.40 History History: Cr. Register, September, 1990, No. 417, eff. 10-1-90.
NR 230.401 NR 230.401Specialized definitions. The following definitions apply to the terms used in this subchapter:
NR 230.401(1) (1) “Contaminated nonprocess wastewater" means any water which, during manufacturing or processing, comes into incidental contact with any raw material, intermediate product, finished product, byproduct, or waste product.
NR 230.401(2) (2) “Incidental contact" means contact resulting from:
NR 230.401(2)(a) (a) Rainfall runoff;
NR 230.401(2)(b) (b) Accidental spills;
NR 230.401(2)(c) (c) Accidental leaks which are caused by failure of process equipment and which are repaired within the shortest reasonable time not to exceed 24 hours after discovery; and
NR 230.401(2)(d) (d) Discharges from safety showers and related personal safety equipment.
NR 230.401(3) (3) “Process wastewater" means any water which, during manufacturing or processing, comes into contact with or results from the production or use of any raw material, intermediate product, finished product, byproduct, or waste product, except for contaminated nonprocess wastewater.
NR 230.401(4) (4) “Process wastewater pollutants" means pollutants present in the process wastewater.
NR 230.401 History History: Cr. Register, September, 1990, No. 417, eff. 10-1-90.
NR 230.4015 NR 230.4015Regulation of contaminated nonprocess wastewater. Contaminated nonprocess wastewater shall be regulated as process wastewater unless all reasonable measures have been taken to prevent, reduce, and control incidental contact and to mitigate the effects of incidental contact after it has occurred.
NR 230.4015 History History: Cr. Register, September, 1990, No. 417, eff. 10-1-90.
NR 230.402 NR 230.402Effluent limitations representing the degree of effluent reduction attainable by the application of the best practicable control technology currently available. Except as provided in 40 CFR 125.30 to 125.32, any existing point source subject to this subchapter may not discharge process wastewater pollutants into waters of the state.
NR 230.402 History History: Cr. Register, September, 1990, No. 417, eff. 10-1-90.
NR 230.406 NR 230.406Pretreatment standards for new sources. Except as provided in s. NR 211.13, any new source subject to this subchapter which introduces pollutants into a POTW shall comply with ch. NR 211 and may not discharge process wastewater pollutants into a POTW.
NR 230.406 History History: Cr. Register, September, 1990, No. 417, eff. 10-1-90.
subch. XLI of ch. NR 230 Subchapter XLI — Hydrogen
NR 230.41 NR 230.41Applicability; description of the hydrogen subcategory. This subchapter applies to the discharge of pollutants to waters of the state and the introduction of pollutants into POTWs from the production of hydrogen as a refinery byproduct.
NR 230.41 History History: Cr. Register, September, 1990, No. 417, eff. 10-1-90.
NR 230.411 NR 230.411Specialized definitions. The following definitions apply to the terms used in this subchapter:
NR 230.411(1) (1) “Contaminated nonprocess wastewater" means any water which, during manufacturing or processing, comes into incidental contact with any raw material, intermediate product, finished product, byproduct, or waste product, if all reasonable measures have been taken to prevent, reduce, and control incidental contact and to mitigate the effects of incidental contact after it has occurred.
Loading...
Loading...
Published under s. 35.93, Stats. Updated on the first day of each month. Entire code is always current. The Register date on each page is the date the chapter was last published.