NR 465.43(2)(c)(c) Emission rate with add-on controls option. You shall meet all the requirements of s. NR 465.48 to demonstrate compliance with the emission limits in sub. (1), the operating limits in sub. (3) and the work practice standards in sub. (4) using this option. To use this option, you shall demonstrate that, based on the coatings, thinners and other additives, and cleaning materials used in the coating operation or operations, and the emissions reductions achieved by emission capture systems and add-on controls, the organic HAP emission rate for the coating operation or operations is less than or equal to the applicable emission limit in sub. (1), calculated as a rolling 12-month emission rate and determined on a monthly basis. If you use this compliance option, you shall also demonstrate that all emission capture systems and add-on control devices for the coating operation or operations meet the operating limits required in sub. (3), except for solvent recovery systems for which you conduct liquid-liquid material balances according to s. NR 465.48 (2) (j), and that you meet the work practice standards required in sub. (4).
NR 465.43(3)(3)What operating limits must i meet?
NR 465.43(3)(a)(a) For any coating operation or operations on which you use the compliant material option specified in sub. (2) (a) or the emission rate without add-on controls option specified in sub. (2) (b), you are not required to meet any operating limits.
NR 465.43(3)(b)(b) For any controlled coating operation or operations on which you use the emission rate with add-on controls option specified in sub. (2) (c), except those for which you use a solvent recovery system and conduct a liquid-liquid material balance according to s. NR 465.48 (2) (j), you shall meet the operating limits specified in Table 1 of this subchapter. These operating limits apply to the emission capture and control systems on the coating operations for which you use this option, and you shall establish the operating limits during the performance test according to the requirements in s. NR 465.48 (8). You shall meet the operating limits at all times after you establish them.
NR 465.43(3)(c)(c) If you use an add-on control device other than those listed in Table 1 of this subchapter, or wish to monitor an alternative parameter and comply with a different operating limit, you shall apply to the administrator for approval of alternative monitoring under 40 CFR 63.8(f).
NR 465.43(4)(4)What work practice standards shall i meet?
NR 465.43(4)(a)(a) For any coating operation or operations on which you use the compliant material option specified in sub. (2) (a) or the emission rate without add-on controls option specified in sub. (2) (b), you are not required to meet any work practice standards.
NR 465.43(4)(b)(b) If you use the emission rate with add-on controls option in sub. (2) (c), you shall develop and implement a work practice plan to minimize organic HAP emissions from the storage, mixing and conveying of coatings, thinners, other additives and cleaning materials used in, and waste materials generated by the controlled coating operations for which you use this option; or you shall meet an alternative standard as provided in par. (c). The plan shall specify practices and procedures to ensure that, at a minimum, the elements specified in subds. 1. to 5. are implemented.
NR 465.43(4)(b)1.1. All organic-HAP-containing coatings, thinners, other additives, cleaning materials and waste materials shall be stored in closed containers.
NR 465.43(4)(b)2.2. Spills of organic-HAP-containing coatings, thinners, other additives, cleaning materials and waste materials shall be minimized.
NR 465.43(4)(b)3.3. Organic-HAP-containing coatings, thinners, other additives, cleaning materials and waste materials shall be conveyed from one location to another in closed containers or pipes.
NR 465.43(4)(b)4.4. Mixing vessels which contain organic-HAP-containing coatings and other materials shall be closed except when adding to, removing or mixing the contents.
NR 465.43(4)(b)5.5. Emissions of organic HAP shall be minimized during cleaning of storage, mixing and conveying equipment.
NR 465.43(4)(c)(c) As provided in 40 CFR 63.6(g), the U. S. EPA may choose to grant you permission to use an alternative to the work practice standards in this subsection.
NR 465.43 HistoryHistory: CR 05-040: cr. Register February 2006 No. 602, eff. 3-1-06.
NR 465.44NR 465.44General compliance requirements.
NR 465.44(1)(1)What are my general requirements for complying with this subchapter?
NR 465.44(1)(a)(a) You shall be in compliance with the emission limits in this subchapter as specified in subds. 1. and 2.
NR 465.44(1)(a)1.1. Any coating operation or operations for which you use the compliant material option or the emission rate without add-on controls option shall be, as specified in s. NR 465.43 (2) (a) and (b), in compliance with the applicable emission limit in s. NR 465.43 (1) at all times.
NR 465.44(1)(a)2.2. Any coating operation or operations for which you use the emission rate with add-on controls option shall be, as specified in s. NR 465.43 (2) (c), in compliance with the emission limits as specified in subd. 2. a. to c.
NR 465.44(1)(a)2.a.a. The coating operation or operations shall be in compliance with the applicable emission limit in s. NR 465.43 (1) at all times except during periods of startup, shutdown and malfunction.
NR 465.44(1)(a)2.b.b. The coating operation or operations shall be in compliance with the operating limits for emission capture systems and add-on control devices required by s. NR 465.43 (3) at all times except during periods of startup, shutdown and malfunction, and except for solvent recovery systems for which you conduct liquid-liquid material balances according to s. NR 465.48 (2) (j).
NR 465.44(1)(a)2.c.c. The coating operation or operations shall be in compliance with the work practice standards in s. NR 465.43 (4) at all times.
NR 465.44(1)(b)(b) You shall always operate and maintain your affected source, including all air pollution control and monitoring equipment you use for purposes of complying with this subchapter, according to the provisions in s. NR 460.05 (4) (a) 1.
NR 465.44(1)(c)(c) If your affected source uses an emission capture system and add-on control device, you shall develop and implement a written startup, shutdown and malfunction plan according to the provisions in s. NR 460.05 (4) (c). The plan shall address the startup, shutdown and corrective actions in the event of a malfunction of the emission capture system or the add-on control device. The plan shall also address any coating operation equipment that may cause increased emissions or that would affect capture efficiency if the process equipment malfunctions, such as conveyors that move parts among enclosures.
NR 465.44(2)(2)What parts of the general provisions apply to me? You shall comply with the applicable general provisions requirements in ch. NR 460. Appendix MMMM in ch. NR 460 shows which parts of the general provisions in ch. NR 460 apply to you.
NR 465.44 HistoryHistory: CR 05-040: cr. Register February 2006 No. 602, eff. 3-1-06.
NR 465.45NR 465.45Notifications, reports and records.
NR 465.45(1)(1)What notifications must i submit?