NR 466.03(31)(31) Mvu is the mass of volatile matter, including water, used in a month, in kg (lb). NR 466.03(32)(32) MWi is the molecular weight of compound i in the vent gas, kg/kg-mol. NR 466.03(33)(33) n is the number of organic compounds in the vent gas. NR 466.03(34)(34) p is the number of different inks, coatings, varnishes, adhesives, primers and other solids-containing materials applied in a month. NR 466.03(35)(35) q is the number of different solvents, thinners, reducers, diluents or other non-solids-containing materials applied in a month. NR 466.03(36)(36) Qsd is the volumetric flow rate of gases entering or exiting the control device in dscm/hr, as determined by Method 2 in 40 CFR Part 60, Appendix A, incorporated by reference in s. NR 484.04. NR 466.03(37)(37) R is the overall organic HAP control efficiency as a percent. NR 466.03(38)(38) Re is the overall effective organic HAP control efficiency for publication rotogravure as a percent. NR 466.03(39)(39) Rv is the organic volatile matter collection and recovery efficiency as a percent. NR 466.03(40)(40) S is the mass organic HAP emission rate per mass of material applied, in kg/kg (lb/lb). NR 466.03(41)(41) 0.0416 is the conversion factor for molar volume, kg-mol/m3, at standard conditions. NR 466.03 HistoryHistory: Cr. Register, March, 2000, No. 531, eff. 4-1-00. NR 466.05NR 466.05 Standards: general. General provisions of ch. NR 460 apply to owners and operators of affected sources subject to this chapter as indicated in ch. NR 460 Appendix KK. NR 466.05 HistoryHistory: Cr. Register, March, 2000, No. 531, eff. 4-1-00. NR 466.06NR 466.06 Standards: publication rotogravure printing. NR 466.06(1)(1) Compliance dates. Each owner or operator of any publication rotogravure printing affected source that is subject to the requirements of this chapter shall comply with this section on and after the compliance dates as specified in s. NR 466.08. NR 466.06(2)(2) Emission limitation. The owner or operator of each publication rotogravure affected source shall limit organic HAP emissions to no more than 8% of the total volatile matter used each month. NR 466.06(3)(3) Compliance methods. The emission limitation in sub. (2) shall be achieved by any of the following methods: NR 466.06(3)(c)(c) A combination of capture and control technologies and substitution of materials. NR 466.06(4)(a)(a) Solvent recovery. Each owner or operator using a solvent recovery device to control emissions shall demonstrate compliance by showing that the HAP emission limitation is achieved by doing either of the following: NR 466.06(4)(a)1.1. Perform a liquid-liquid material balance for each month according to the following procedures: NR 466.06(4)(a)1.a.a. Measure the mass of each ink, coating, varnish, adhesive, primer, solvent and other material used by the affected source during the month. NR 466.06(4)(a)1.b.b. Determine the organic HAP content of each ink, coating, varnish, adhesive, primer, solvent and other material used by the affected source during the month following the procedure in s. NR 466.09 (2) (a). NR 466.06(4)(a)1.c.c. Determine the volatile matter content, including water, of each ink, coating, varnish, adhesive, primer, solvent and other material used by the affected source during the month following the procedure in s. NR 466.09 (3) (a). NR 466.06(4)(a)1.d.d. Install, calibrate, maintain and operate, according to the manufacturer’s specifications, a device that indicates the cumulative amount of volatile matter recovered by the solvent recovery device on a monthly basis. The device shall be initially certified by the manufacturer to be accurate to within +2.0%.