NR 440.705(7)(a)(a) For purposes of this section “fixed capital cost of the new components,” as used in s. NR 440.15, includes the fixed capital cost of all depreciable components which are or will be replaced pursuant to all continuous programs of component replacement which are commenced within any 2 year period following June 29, 1990. For purposes of this paragraph,“commenced” means that an owner or operator has undertaken a continuous program of component replacement or that an owner or operator has entered into a contractual obligation to undertake and complete, within a reasonable time, a continuous program of component replacement. 1CAS numbers refer to the Chemical Abstracts Registry numbers assigned to specific chemicals, isomers or mixtures of chemicals. Some isomers or mixtures that are covered by the standards do not have CAS numbers assigned to them. The standards apply to all of the chemicals listed whether CAS numbers have been assigned or not.
NR 440.705 HistoryHistory: Cr., Register, December, 1995, No. 480, eff. 1-1-96; CR 06-109: am. (1) (c) 2., 3. and 4., (5) (d) 2. b. and 4., (e) 1. a. and (f) 1., (6) (L) 1., 4., 5. and 8. and (8), cr. (1) (d) Register May 2008 No. 629, eff. 6-1-08; correction in (1) (d) 2. made under s. 13.92 (4) (b) 7., Stats., Register May 2008 No. 629. NR 440.71NR 440.71 Magnetic tape coating facilities. NR 440.71(1)(1) Applicability and designation of affected facility. NR 440.71(1)(a)(a) The affected facilities to which the provisions of this section apply are: NR 440.71(1)(b)(b) Any new coating operation that utilizes less than 38 m3 of solvent or any modified or reconstructed coating operation that utilizes less than 370 m3 of solvent for the manufacture of magnetic tape per calendar year is subject only to the requirements of subs. (5) (a) and (8) (b) and (c). If the amount of solvent utilized for the manufacture of magnetic tape equals or exceeds these amounts in any calendar year, the facility is subject to sub. (3) and all other paragraphs of this section. Once a facility has become subject to sub. (3) and all other paragraphs of this section, it shall remain subject to those requirements regardless of changes in annual solvent utilization. NR 440.71(1)(c)(c) This section applies to any affected facility for which construction, modification or reconstruction begins after January 22, 1986. NR 440.71(2)(2) Definitions, symbols and cross reference tables. NR 440.71(2)(a)(a) All terms used in this section that are not defined as follows have the meaning given to them in s. NR 440.02. NR 440.71(2)(a)1.1. “Base film” means the substrate that is coated to produce magnetic tape. NR 440.71(2)(a)2.2. “Capture system” means any device or combination of devices that contains or collects an airborne pollutant and directs it into a duct. NR 440.71(2)(a)3.3. “Coating applicator” means any apparatus used to apply a coating to a continuous base film. NR 440.71(2)(a)4.4. “Coating mix preparation equipment” means all mills, mixers, holding tanks, polishing tanks and other equipment used in the preparation of the magnetic coating formulation but does not include those mills that do not emit VOC because they are closed, sealed and operated under pressure. NR 440.71(2)(a)5.5. “Coating operation” means any coating applicator, flashoff area and drying oven located between a base film unwind station and a base film rewind station that coat a continuous base film to produce magnetic tape. NR 440.71(2)(a)6.6. “Common emission control device” means a control device controlling emissions from the coating operation as well as from another emission source within the plant. NR 440.71(2)(a)7.7. “Concurrent” means construction of a control device is commenced or completed within the period beginning 6 months prior to the date construction of affected coating mix preparation equipment commences and ending 2 years after the date construction of affected coating mix preparation equipment is completed. NR 440.71(2)(a)8.8. “Control device” means any apparatus that reduces the quantity of a pollutant emitted to the air. NR 440.71(2)(a)9.9. “Cover” means, with respect to coating mix preparation equipment, a device that lies over the equipment opening to prevent VOC from escaping and that meets the requirements found in sub. (3) (e) 1. to 5. NR 440.71(2)(a)10.10. “Drying oven” means a chamber in which heat is used to bake, cure, polymerize or dry a surface coating. NR 440.71(2)(a)11.11. “Equivalent diameter” means 4 times the area of an opening divided by its perimeter. NR 440.71(2)(a)12.12. “Flashoff area” means the portion of a coating operation between the coating applicator and the drying oven where solvent begins to evaporate from the coated base film. NR 440.71(2)(a)13.13. “Magnetic tape” means any flexible substrate that is covered on one or both sides with a coating containing magnetic particles and that is used for audio or video recording or information storage.