ATCP 93.100(2)(d) (d) The location, size and capacity of each tank and the following information on the contents of the tank:

ATCP 93.100(2)(d)1. 1. The name of the stored liquid.

ATCP 93.100(2)(d)2. 2. The flammability or combustibility classification of the stored liquid.

ATCP 93.100 Note Note: Flammability and combustibility classifications are established in NFPA 30 sections 4.3.1 and 4.3.2, and are expressed as a Roman numeral and a letter, such as IB or IIIA.

ATCP 93.100(2)(d)3. 3. Whether the stored liquid is classified in any of the following hazard categories as defined in the applicable model fire code adopted by reference under ch. SPS 314:

ATCP 93.100(2)(d)3.a. a. Explosive or pyrophoric.

ATCP 93.100(2)(d)3.b. b. Oxidizer or organic peroxide.

ATCP 93.100(2)(d)3.c. c. Unstable or water reactive.

ATCP 93.100(2)(d)3.d. d. Toxic or highly toxic.

ATCP 93.100(2)(d)3.e. e. Cryogenic or corrosive to living tissue.

ATCP 93.100(2)(e) (e) The location of all piping runs and spacing between all tanks and piping.

ATCP 93.100(2)(f) (f) The type of tank supports and clearances, including clearances between tanks.

ATCP 93.100(2)(g) (g) The type of venting and pressure relief used and combined capacity of all venting and relief valves on each aboveground tank.

ATCP 93.100(2)(h) (h) The location of fill, gauge and vent pipes and other openings for the tank.

ATCP 93.100(2)(i) (i) The location of burners, tanks, pumps, piping and control valves and the relative elevations of any areas within the building where heavier-than-air vapors can accumulate.

ATCP 93.100(2)(j) (j) The distances to dispensers, sizes of islands and traffic flow patterns or vehicle routes around or through the facility.

ATCP 93.100(2)(k) (k) Information and specifications describing the design and placement of leak detection systems.

ATCP 93.100(2)(L) (L)

ATCP 93.100(2)(L)1. 1. Information regarding the type and operation of corrosion protection systems for tanks and piping.

ATCP 93.100(2)(L)2. 2. For impressed current systems, the location and materials of gas mains and gas service lines serving the facility.

ATCP 93.100(2)(m) (m) Information regarding the type of secondary containment system.

ATCP 93.100(2)(n) (n) Specifications describing the spill and overfill protection devices.

ATCP 93.100(2)(o) (o) Information regarding the compatibility of the tank and piping system with the regulated substance.

ATCP 93.100(2)(p) (p) A copy of any easement that reflects any property not owned by the system operator on which any portion of the system is located or any vehicle is parked while transferring product.

ATCP 93.100(2)(q) (q) Any material-approval numbers issued under s. ATCP 93.130.

ATCP 93.100(2)(r) (r) Information and specifications, including manufacturer’s model numbers on materials, equipment and devices to be used in the project which do not have material-approval numbers issued under s. ATCP 93.130 and which have a direct impact on the regulated system.

ATCP 93.100 Note Note: Examples of this equipment include valves, nozzles and hoses.

ATCP 93.100(2)(s) (s) Additional data and information regarding storage of regulated substances within buildings or enclosures to demonstrate compliance with the requirements of this chapter.

ATCP 93.100(2)(t) (t) Any other information necessary for the reviewer to determine code compliance.