NR 463.11(1)(1) The requirements of this subchapter apply to the owner or operator of each secondary aluminum production facility. NR 463.11 NoteNote: This subchapter is based on the federal regulations contained in 40 CFR part 63 Subpart RRR, created March 23, 2000, as last revised on April 20, 2006. NR 463.11(2)(2) The requirements of this subchapter apply to the following affected sources, located at a secondary aluminum production facility that is a major source of hazardous air pollutants (HAPs) as defined in s. NR 460.02 (22): NR 463.11(2)(c)(c) Each new and existing scrap dryer, delacquering kiln and decoating kiln. NR 463.11(2)(h)(h) Each new and existing secondary aluminum processing unit. NR 463.11(3)(3) The requirements of this subchapter pertaining to dioxin and furan emissions and associated operating, monitoring, reporting and recordkeeping requirements apply to the following affected sources, located at a secondary aluminum production facility that is an area source of HAPs as defined in s. NR 460.02 (5): NR 463.11(3)(b)(b) Each new and existing scrap dryer, delacquering kiln and decoating kiln. NR 463.11(3)(d)(d) Each new and existing secondary aluminum processing unit, containing one or more group 1 furnace emission units processing other than clean charge. NR 463.11(4)(4) The requirements of this subchapter do not apply to facilities and equipment used for research and development that are not used to produce a salable product. NR 463.11(5)(5) An aluminum die casting facility, aluminum foundry or aluminum extrusion facility shall be considered to be an area source if it does not emit, or have the potential to emit, considering controls, 10 tons per year or more of any single listed HAP or 25 tons per year of any combination of listed HAP from all emission sources which are located in a contiguous area and under common control, without regard to whether or not the sources are regulated under this subchapter or any other subchapter. In the case of an aluminum die casting facility, aluminum foundry or aluminum extrusion facility which is an area source and is subject to regulation under this subchapter only because it operates a thermal chip dryer, no furnace operated by such a facility shall be deemed to be subject to the requirements of this subchapter if it melts only clean charge, internal scrap or customer returns. NR 463.11 HistoryHistory: CR 04-023: cr. Register December 2008 No. 636, eff. 1-1-09. NR 463.115(1)(1) The owner or operator of an existing affected source shall comply with the requirements of this subchapter by March 24, 2003. NR 463.115(2)(2) Except as provided in sub. (3), the owner or operator of a new affected source that commences construction or reconstruction after February 11, 1999 shall comply with the requirements of this subchapter by March 24, 2000 or upon startup, whichever is later. NR 463.115(3)(3) The owner or operator of any affected source which is constructed or reconstructed at any existing aluminum die casting facility, aluminum foundry or aluminum extrusion facility which otherwise meets the applicability criteria in s. NR 463.11 shall comply with the requirements of this subchapter by March 24, 2003 or upon startup, whichever is later. NR 463.115 HistoryHistory: CR 04-023: cr. Register December 2008 No. 636, eff. 1-1-09. NR 463.12NR 463.12 Definitions. For terms not defined in this section, the definitions contained in chs. NR 400 and 460 apply to the terms in this subchapter, with definitions in ch. NR 460 taking priority over definitions in ch. NR 400. If this section defines a term which is also defined in ch. NR 400 or 460, the definition in this section applies in this subchapter. In this subchapter: NR 463.12(1)(1) “Add-on air pollution control device” means equipment installed on a process vent that reduces the quantity of a pollutant that is emitted to the air. NR 463.12(2)(2) “Afterburner” means an air pollution control device that uses controlled flame combustion to convert combustible materials to noncombustible gases; also known as an incinerator or a thermal oxidizer. NR 463.12(3)(3) “Aluminum scrap” means fragments of aluminum stock removed during manufacturing, manufactured aluminum articles or parts rejected or discarded and useful only as material for reprocessing, and waste and discarded material made of aluminum.