ATCP 70.12(3)(3) C-I-P systems. C-I-P systems shall be of sanitary design and construction, and shall be installed and maintained for sanitary operation. A C-I-P system shall be installed and maintained so that cleaning and sanitizing solutions can be circulated throughout all interior product contact surfaces of the system. C-I-P systems shall be equipped with adequate inspection ports or other access points. C-I-P systems shall be self-draining, or shall be capable of being easily and completely drained. A temperature recording device, which accurately records the return temperatures of cleaning and sanitizing solutions, shall be installed in all circuits through which cleaning and sanitizing solutions are circulated. Cleaning records shall be kept for at least 90 days after they are created.

ATCP 70.12(4)(4) Location and installation of equipment. Equipment that cannot be easily moved shall be installed in a manner preventing liquid or debris from accumulating under or around the equipment. Equipment shall be installed so there is adequate clearance on all sides for cleaning and maintenance. This does not apply to that portion of a tank or container designed and installed to protrude into or through the wall or ceiling of a food processing plant. Air intake vents for food or ingredient storage containers shall be located in processing areas or shall be properly filtered.

ATCP 70.12(5)(5) Measuring devices and controls. Every freezer and cold storage compartment used to store or hold potentially hazardous food shall be equipped with a thermometer or other device accurately indicating the temperature in the compartment. Instruments and controls used for measuring, regulating, and recording temperatures, pH, acidity, water activity, or other conditions that control or prevent the growth of undesirable microorganisms in food shall be accurate and adequate for their intended use.

ATCP 70.12(6)(6) Lubrication. Equipment shall be designed and constructed so gear and bearing lubricants do not come in contact with food or food contact surfaces. Only food grade lubricants may be used in equipment if incidental food contact may occur.

ATCP 70.14(1)(1) General. Except as provided in ss. ATCP 70.16 and 70.40, the operator shall do all of the following:

ATCP 70.14(1)(b)(b) Except as provided in pars. (c), (d) and (e), clean all food contact surfaces of equipment and utensils after each day’s use, and before any change in use that may cross-contaminate food with major food allergens or other contaminants. If wet cleaning occurs, surfaces must also be sanitized.

ATCP 70.14(1)(c)(c) Clean and sanitize tanks, used to store potentially hazardous food or potentially hazardous food ingredients, at least once after the food processing plant operator empties those tanks.

ATCP 70.14(1)(d)(d) Clean and sanitize all food contact surfaces of equipment used for the distillation of alcohol products, such as distilled spirits, after each distillation batch. This paragraph does not apply to equipment used to distill smoke for the manufacture of liquid smoke products.

ATCP 70.14(1)(e)(e) Request alternative cleaning and sanitizing procedures for department approval, under ss. ATCP 70.16 and 70.18, as provided in those sections.

ATCP 70.14(2)(2) Cleaning and sanitizing c-i-p systems. C-I-P systems shall be cleaned and sanitized in compliance with manufacturer specifications. Cleaning and sanitizing records shall be maintained for all C-I-P systems. The records shall identify every C-I-P system which has been cleaned or sanitized, the date and time when each C-I-P system was cleaned and sanitized, the temperature of the cleaning and sanitizing solutions, and the length of time for which the C-I-P system was exposed to each cleaning and sanitizing solution. Records shall be signed or initialed by a responsible person, maintained on file for at least 90 days, and made available for inspection and copying by the department upon request.

ATCP 70.14(3)(3) Cleaning compounds, detergents, and sanitizers: storage and labeling. Cleaning compounds, detergents, and sanitizers shall be clearly labeled. When they are not being used, they shall be stored in designated areas and in an appropriate manner so that they do not contaminate food products, ingredients, equipment, or utensils.

ATCP 70.14(4)(4) Storage of clean equipment and utensils. Equipment and utensils, unless stored in an approved sanitizing solution, shall be stored so as to drain dry. Equipment and utensils shall be protected from contamination prior to use.

ATCP 70.14(5)(5) Single-service articles. Single-service articles shall be stored in the original containers in which they were received, or in other closed containers which will protect them from contamination prior to use. Single-service articles shall not be re-used.

ATCP 70.14(6)(6) Equipment and utensils in egg handling facilities. Equipment for candling, grading, and weighing eggs shall meet the requirements of s. ATCP 88.12 (5).

ATCP 70.14(7)(7) Equipment and utensils in maple sap concentration facilities. The equipment and utensils in a facility used solely for the concentration of maple sap shall conform to the applicable regulations in s. ATCP 87.26.

ATCP 70.14 HistoryHistory: CR 17-073: cr. Register January 2020 No. 769, eff. 2-1-20; correction in (1) (b) made under s. 35.17, Stats., Register January 2020 No. 769.

ATCP 70.16(1)(1) Approval required for an alternative cleaning and sanitizing frequency.

ATCP 70.16(1)(ag)(ag) Except as provided in sub. (2) or s. ATCP 70.40, if an operator seeks to clean and sanitize equipment and utensils at a frequency other than that required in s. ATCP 70.14 (1), because the equipment and utensils are used with food products, processes, or conditions reducing the risk of foodborne illness or presence of major food allergens, then the operator shall submit to the department, for written approval, an alternate cleaning and sanitizing procedure that includes a monitoring and recording requirement in compliance with s. ATCP 70.18.

ATCP 70.16(1)(ar)(ar) Factors reducing the risk of foodborne illness may include competitive microorganisms, intended use or targeted consumer demographic, inhibitory compounds, temperatures, and any other factors that reduce the risk of pathogenic organism growth or toxin formation.

ATCP 70.16(1)(b)(b) After review by the department, the proposed process may be denied and the department shall issue a letter of denial. If the alternate cleaning and sanitizing procedure is approved, the department shall issue a letter of approval, applicable for not more than 5 years, which shall be maintained on file at the food processing plant.

ATCP 70.16(1)(c)(c) If a change is planned for the product or any process that affects the critical factors ensuring the safety of that product, the operator shall inform the department in writing prior to making a change.

ATCP 70.16(2)(2) No approval required for an alternative cleaning and sanitizing frequency. An operator is not required to obtain written department approval for use of an alternative equipment and utensil cleaning and sanitizing frequency for the following equipment, provided that the operator cleans and sanitizes the equipment according to manufacturer specifications or according to a validated cleaning process filed with the department: