NR 466.07(4)(a)2.e.e. Install, calibrate, operate and maintain the instrumentation necessary to measure continuously the site-specific operating parameter established in accordance with s. NR 466.10 (6) whenever a product and packaging rotogravure or wide-web flexographic printing press is operated. NR 466.07(4)(a)2.g.g. Calculate the overall organic HAP control efficiency, (R), achieved for each month using Equation 13. NR 466.07(4)(a)2.h.h. If demonstrating compliance with sub. (2) (b), (c) or (d), calculate the organic HAP emitted during the month, H, for each month using Equation 14. (Equation 14)
NR 466.07(4)(a)2.i.i. If demonstrating compliance with sub. (2) (c), calculate the organic HAP emission rate based on solids applied, L, using Equation 15. NR 466.07(4)(a)2.j.j. If demonstrating compliance with sub. (2) (b), calculate the organic HAP emission rate based on material applied, S, using Equation 16. NR 466.07(4)(b)1.1. Under par. (a) 1., the affected source is in compliance with an emission limitation if one of the following is satisfied: NR 466.07(4)(b)1.a.a. The organic volatile matter collection and recovery efficiency, Rv, is 95% or greater. NR 466.07(4)(b)1.b.b. The organic HAP emission rate based on solids applied, L, is 0.20 kg (0.20 lb) organic HAP per kg (lb) solids applied or less. NR 466.07(4)(b)1.c.c. The organic HAP emission rate based on material applied, S, is 0.04 kg (0.04 lb) organic HAP per kg (lb) material applied or less. NR 466.07(4)(b)1.d.d. The organic HAP emitted during the month, H, is less than the calculated allowable organic HAP, Ha, as determined using sub. (6). NR 466.07(4)(b)2.2. Under par. (a) 2., the affected source is in compliance with an emission limitation if the capture system operating parameter is operated at an average value greater than or less than, as appropriate, the operating parameter value established in accordance with s. NR 466.10 (6) for each 3 hour period, and one of the following is satisfied: NR 466.07(4)(b)2.a.a. The organic volatile matter collection and recovery efficiency, Rv, is 95% or greater. NR 466.07(4)(b)2.b.b. The organic HAP emission rate based on solids applied, L, is 0.20 kg (0.20 lb) organic HAP per kg (lb) solids applied or less. NR 466.07(4)(b)2.c.c. The organic HAP emission rate based on material applied, S, is 0.04 kg (0.04 lb) organic HAP per kg (lb) material applied or less. NR 466.07(4)(b)2.d.d. The organic HAP emitted during the month, H, is less than the calculated allowable organic HAP, Ha, as determined using sub. (6). NR 466.07(5)(a)(a) To demonstrate the overall organic HAP control efficiency required under sub. (3) (g) or the organic HAP emission limitation requirements in sub. (3) (h) to (j), each owner or operator using an oxidizer to control emissions shall do one of the following: NR 466.07(5)(a)1.1. Conduct initial performance tests of capture efficiency and control device efficiency and continuously monitor capture system and control device operating parameters according to the following procedures: NR 466.07(5)(a)1.d.d. If demonstrating compliance with sub. (2) (b), (c) or (d), measure the mass of each ink, coating, varnish, adhesive, primer, solvent and other material applied on the press or group of presses controlled by a common solvent recovery device during the month.