Chapter NR 422

Register July 2009 No. 643

Chapter NR 422

CONTROL OF ORGANIC COMPOUND EMISSIONS
FROM SURFACE COATING, PRINTING AND ASPHALT SURFACING OPERATIONS

NR 422.01   Applicability; purpose.

NR 422.02   Definitions.

NR 422.03   Exemptions.

NR 422.04   Methods of compliance.

NR 422.05   Can coating.

NR 422.06   Coil coating.

NR 422.07   Paper coating — part 1.

NR 422.075   Paper coating — part 2.

NR 422.08   Fabric and vinyl coating.

NR 422.083   Plastic parts coating — part 1.

NR 422.084   Plastic parts coating — part 2.

NR 422.085   Leather coating.

NR 422.09   Automobile and light-duty truck manufacturing.

NR 422.095   Automobile refinishing operations.

NR 422.10   Furniture metal coating — part 1.

NR 422.105   Furniture metal coating — part 2.

NR 422.11   Surface coating of large appliances — part 1.

NR 422.115   Surface coating of large appliance — part 2.

NR 422.12   Magnet wire coating.

NR 422.125   Wood furniture coating.

NR 422.127   Use of adhesives — part 1.

NR 422.128   Use of adhesives — part 2.

NR 422.13   Flat wood panel coating — part 1.

NR 422.131   Flat wood panel coating — part 2.

NR 422.132   Wood door coating.

NR 422.135   Molded wood parts or products.

NR 422.14   Graphic arts.

NR 422.141   Flexible package printing.

NR 422.142   Lithographic printing — part 1.

NR 422.143   Lithographic printing — part 2.

NR 422.144   Letterpress printing.

NR 422.145   Screen printing.

NR 422.15   Miscellaneous metal parts and products — part 1.

NR 422.151   Miscellaneous metal parts and products — part 2.

NR 422.155   Fire truck and emergency response vehicle manufacturing.

NR 422.16   Use of asphalt surfacing materials.

NR 422.17   Application of traffic marking materials.

Ch. NR 422 Note Note: Corrections made under s. 13.93 (2m) (b) 7., Stats., Register, December, 1996, No. 492.

NR 422.01 NR 422.01 Applicability; purpose.

NR 422.01(1) (1) Applicability. This chapter applies to all surface coating and printing process air contaminant sources and to their owners and operators. This chapter also applies to the handling and use of cutback asphalts for application to surfaces traversed by motor vehicles, bicycles or pedestrians and to all persons responsible for such handling and use.

NR 422.01(2) (2) Purpose. This chapter is adopted under ss. 285.11, 285.13 and 285.17, Stats., to categorize organic compound emissions from surface coating, printing and asphalt surfacing operations into separate organic compound air contaminant source categories and to establish emission limitations or other requirements for these categories of sources in order to protect air quality.

NR 422.01(3) (3) For a source located in an area that was ever designated nonattainment for ozone that had VOC emissions exceeding the applicability emission thresholds and became subject to the requirements of this chapter, the requirements of this chapter remain applicable notwithstanding any subsequent decrease in VOC emissions to a level below the applicability emission thresholds.

NR 422.01(4) (4) The department may exempt a source from the requirements of this chapter if the source has an approved federally enforceable permit or state implementation plan revision that permanently restricts maximum theoretical emissions to below the applicability emission thresholds listed under this chapter and meets all applicable federal VOC RACT exemption requirements.

NR 422.01 Note Note: “Maximum theoretical emissions” referred to in this chapter is defined under s. NR 419.02 (11).

NR 422.01 History History: Cr. Register, September, 1986, No. 369, eff. 10-1-86; am. Register, February, 1990, No. 410, eff. 3-1-90; CR 20-088: cr. (3), (4) Register May 2022 No. 797, eff. 6-1-22.

NR 422.02 NR 422.02 Definitions. Except when another definition is specifically made applicable, the definitions contained in chs. NR 400, 419, and 421 apply to the terms used in this chapter. In addition, except when another definition is specifically made applicable, in this chapter:

NR 422.02(1d) (1d) “Acrylonitrile-butadiene-styrene welding” or “ABS welding” means any process to weld acrylonitrile-butadiene-styrene pipe.

NR 422.02(1h) (1h) “Adhesion primer” means a coating that is applied to a polyolefin part to promote the adhesion of a subsequent coating and that is clearly identified as an adhesion primer or adhesion promoter on its accompanying material safety data sheet.

NR 422.02(1m) (1m) “Adhesion promoter” means a coating designed to facilitate the bonding of a primer or topcoat on surfaces such as trim moldings, door locks and door sills, where sanding is impractical, and on plastic parts and the edges of sanded areas.

NR 422.02(2) (2) “Adhesive” means any substance that is used to bond one surface to another surface by attachment.

NR 422.02(3) (3) “Adhesive primer” means a coating that is applied directly to a substrate in order to seal the substrate and to provide a bonding surface for an adhesive prior to the application of the adhesive.

NR 422.02(3g) (3g) “Aerosol adhesive” means an adhesive or adhesive primer packaged as an aerosol product in which the spray mechanism is permanently housed in a non-refillable can designed for handheld application without the need for ancillary hoses or spray equipment.

NR 422.02(3r) (3r) “Air assisted airless spray” means a spray coating method that combines compressed air with hydraulic pressure to atomize the coating material into finer droplets than is achieved with pure airless spray. Lower hydraulic pressure is used than with airless spray.

NR 422.02(4) (4) “Air dried coating” means coatings which are dried by the use of air or forced warm air. Forced warm air includes processes whereby the coated object is heated above ambient temperature up to a maximum of 90°C (194°F) to decrease drying time.