This is the preview version of the Wisconsin State Legislature site.
Please see http://docs.legis.wisconsin.gov for the production version.
SPS 384.25   POWTS holding components or treatment components.
SPS 384.30   Plumbing materials.
SPS 384.40   Joints and connections.
SPS 384.50   Alternate approvals and experimental approvals.
Ch. SPS 384 Note Note: Chapter ILHR 84 as it existed on May 31, 1988 was repealed and a new chapter ILHR 84 was created effective June 1, 1988. Chapter ILHR 84 was renumbered Comm 84 under s. 13.93 (2m) (b) 1., Stats., and corrections made under s. 13.93 (2m) (b) 7., Stats., Register, February, 1997, No. 494. Chapter Comm 84 was renumbered chapter SPS 384 under s. 13.92 (4) (b) 1., Stats., Register December 2011 No. 672.
SPS 384.01 SPS 384.01Scope.
SPS 384.01(1)(1)The provisions of this chapter govern the quality and installation of materials, fixtures, appliances, appurtenances, and equipment relating to plumbing.
SPS 384.01(2) (2)A department interpretation of the requirements in this chapter shall supersede any differing interpretation by a lower level jurisdiction. A department decision on the application of the requirements in this chapter shall supersede any differing decision by a lower level jurisdiction.
SPS 384.01 Note Note: A decision of the department may be appealed. Section 101.02 (6) (e), Stats., outlines the procedure for submitting requests to the department for appeal hearings and the department procedures for hearing appeals.
SPS 384.01 History History: Cr. Register, May, 1988, No. 389, eff. 6-1-88; CR 07-100: renum. to (1), cr. (2) Register September 2008 No. 633, eff. 10-1-08.
SPS 384.02 SPS 384.02Penalties. Penalties for violations of this chapter shall be assessed in accordance with s. 145.12, Stats.
SPS 384.02 History History: Cr. Register, May, 1988, No. 389, eff. 6-1-88; correction made under s. 13.93 (2m) (b) 7., Stats., Register, July, 2000, No. 535.
SPS 384.10 SPS 384.10Department approval. No fixture, appliance, appurtenance, material, device or product may be sold for use in a plumbing system or may be installed in a plumbing system, unless it is of a type conforming to the standards or specifications of chs. SPS 382 to 384 and ch. 145, Stats.
SPS 384.10(1) (1)Alternate or experimental product approval. If it is alleged that the approval of a fixture, appliance, appurtenance, material, device or product under this section would result in an adverse health effect or potentially adverse health effect on the waters of the state, the department may require an alternate or experimental product approval under s. SPS 384.50.
SPS 384.10(2) (2)Product review and approval.
SPS 384.10(2)(a)1.1. Each type of plumbing product which falls into one of the categories specified in Table 384.10 shall be approved by the department in accordance with this subsection before the product may be sold for use in a plumbing system or installed in a plumbing system.
SPS 384.10(2)(a)2. 2. Specifications and plans or drawings for each type of product shall be submitted to the department for review. The submittal shall be accompanied by sufficient data and information to determine if the product and its performance comply with the provisions of chs. SPS 382 to 384 and ch. 145, Stats.
SPS 384.10(2)(b)1.1. The department may require that a submitter of a product for review have the product tested and its performance certified by an approved testing laboratory.
SPS 384.10(2)(b)2. 2. The department may consult with the technical advisory committee for guidance in the review of submittals under this subsection.
SPS 384.10(2)(c) (c) If, upon review, the department determines that a product conforms to the provisions of chs. SPS 382 to 384 and ch. 145, Stats., the department shall issue an approval in writing. The department may impose specific conditions in granting an approval. Violations of the conditions under which an approval is granted shall constitute a violation of this chapter.
SPS 384.10(2)(d) (d) If, upon review, the department determines that a product does not conform to provisions of chs. SPS 382 to 384 and ch. 145, Stats., the request for approval shall be denied in writing.
SPS 384.10(2)(e) (e) The department shall review and make a determination on an application for a product approval within 40 business days of receipt of all fees, plans, drawings, specifications and other information required to complete the review.
SPS 384.10(2)(f) (f) If an approved plumbing product is modified or additional assertions of function or performance are made, the approval shall be considered null and void, unless the change is submitted to the department for review and the approval is reaffirmed.
SPS 384.10(2)(g) (g) Approvals for plumbing products issued by the department prior to November 1, 1985, shall expire 30 months after the effective date of this section.
SPS 384.10(2)(h) (h) Approvals for plumbing products issued by the department after November 1, 1985, shall expire at the end of the 60th month after the date of approval issuance. - See PDF for table PDF
SPS 384.10 Note Note: More information about the certification bodies accredited by the American National Standards Institute (ANSI), such as the National Sanitation Foundation, is available at the ANSI website at www.ansi.org; or at 1899 L Street, NW, 11th Floor Washington, DC, 20036; or at telephone 202.293.8020.
SPS 384.10(3) (3)Voluntary POWTS component manual review.
SPS 384.10(3)(a)(a) The department may issue an approval, upon request and review, for specific methods or technologies that are proposed to be utilized as POWTS holding, treatment or dispersal components which conform to the standards or specifications referenced in chs. SPS 381to 384, but do not require approval under sub. (2) or s. SPS 384.50.
SPS 384.10(3)(b) (b) Each request for approval shall be made on a form provided by the department.
SPS 384.10 Note Note: See ch. SPS 384 Appendix for a reprint of the form and addresses of the department where the form may be obtained.
SPS 384.10(3)(c) (c) The submittal shall be accompanied by sufficient data and information to determine if the method or technology complies with the provisions of chs. SPS 381 to 384. The submittal shall include all of the following:
SPS 384.10(3)(c)1. 1. Plans and specifications.
SPS 384.10(3)(c)2. 2. Theory of operation.
SPS 384.10(3)(c)3. 3. Testing protocol.
SPS 384.10(3)(c)4. 4. Testing data.
SPS 384.10(3)(c)5. 5. Limits of reliable operation.
SPS 384.10(3)(c)6. 6. Installation requirements and procedures.
SPS 384.10(3)(c)7. 7. Inspection checklist and worksheet.
SPS 384.10(3)(c)8. 8. Inspection requirements and procedures.
SPS 384.10(3)(c)9. 9. Operation and maintenance requirements.
SPS 384.10(3)(c)10. 10. Operation and maintenance schedule.
SPS 384.10(3)(c)11. 11. Operation and maintenance checklist and worksheet.
SPS 384.10(3)(c)12. 12. Other information requested by the department.
SPS 384.10(3)(d)1.1. The department shall review an initial application submitted under this subsection with input from a technical advisory committee.
SPS 384.10(3)(d)2. 2. The members on the technical advisory committee under subd. 1. shall be appointed by the department for staggered 3-year terms and shall include representatives of all of the following groups or organizations:
SPS 384.10(3)(d)2.a. a. A representative of the department of natural resources familiar with large scale POWTS systems to serve as a nonvoting member.
SPS 384.10(3)(d)2.b. b. A representative of a governmental unit responsible for the regulation of POWTS.
SPS 384.10(3)(d)2.c. c. A POWTS designer.
SPS 384.10(3)(d)2.d. d. A member of the academic or scientific community.
SPS 384.10(3)(d)2.e. e. A journeyman or master plumber involved in POWTS installation.
SPS 384.10(3)(d)2.f. f. A professional soil scientist or certified soil tester.
SPS 384.10(3)(d)2.g. g. A POWTS component manufacturer.
SPS 384.10(3)(d)2.h. h. An at-large member.
SPS 384.10(3)(d)2.i. i. A representative from the department of safety and professional services familiar with POWTS approval to serve as a nonvoting member.
SPS 384.10(3)(e)1.1. After review by the technical advisory committee under par. (d) but prior to issuing an approval under par. (f), the department shall seek public comments on new submittals under this subsection.
SPS 384.10(3)(e)2. 2. The department shall provide an opportunity for public comment under subd. 1. for a minimum of 14 days.
SPS 384.10 Note Note: Notices to seek public comment are posted on the department's website at dsps.wi.gov.
SPS 384.10(3)(e)3. 3. If the department receives a significant amount of public comment under subd. 2., the department may elect to recognize the specific method or technology through the rule-making process under ch. 227, Stats.
SPS 384.10(3)(f)1.1. If, upon review, the department determines that the method or technology conforms to the provisions of chs. SPS 381 to 384, the department shall issue an approval in writing.
SPS 384.10(3)(f)2. 2. The department may impose specific conditions in granting an approval, including a provision to provide training to POWTS installers and POWTS inspectors.
SPS 384.10(3)(f)3. 3. Violations of the conditions under which an approval is granted shall constitute a violation of this chapter.
SPS 384.10(3)(g) (g) If, upon review, the department determines that the method or technology does not conform to the provisions of chs. SPS 381 to 384, the request for approval shall be denied in writing.
SPS 384.10(3)(h) (h) The department shall review and make a determination on an application for a method or technology approval within 3 months of receipt of all fees, plans, drawings, specifications and other information required to complete the review, unless the department elects to review the method or technology as part of the rule-making process under ch. 227, Stats.
SPS 384.10(3)(i) (i) If an approved method or technology is modified or additional assertions of function or performance are made, the approval shall be considered null and void, unless the change is submitted to the department for review and the approval is reaffirmed.
SPS 384.10(4) (4)Revocation. The department may revoke any approval issued under this section for any false statements or misrepresentation of facts on which the approval was based, or as a result of the product's failure, or if data indicate a health hazard or threat to the waters of the state.
SPS 384.10(5) (5)Limitations. An approval of a plumbing product by the department may not be construed as an assumption of any responsibility for defects in design, construction or performance of any product nor for any damages that may result. All products shall be installed in accordance with the manufacturer's printed instructions and as specified in chs. SPS 382 to 384. If there is a conflict between the manufacturer's printed instructions and requirements of chs. SPS 382 to 384, the requirements of chs. SPS 382 to 384 shall take precedence.
SPS 384.10(6) (6)Fees. Fees for product approval review shall be submitted in accordance with s. SPS 302.66.
SPS 384.10 History History: Cr. Register, May, 1988, No. 389, eff. 6-1-88; correction made in (6) under s. 13.93 (2m) (b) 7., Stats., Register, February, 1994, No. 458; emerg. am. Table 84.10, (2) (a) (intro.), r. (2) (a) 2., eff. 5-12-94; renum. (2) (a) (intro.), 1. and 2. to be 1., 2. and 3., r. (2) (a) 3., am. Table 84.10, Register, October, 1994, No. 466, eff. 11-1-94; am. Table 84.10 and r. and recr. (3), Register, April, 2000, No. 532, eff. 7-1-00; r. (2) (a) 2., renum. (2) (a) (intro.) and 1. to be (2) (a) 1. and 2. and am. (2) (a) 2., am. (5), (6) and Table 84.10, Register, July, 2000, No. 535, eff. 9-1-00; am. (4) and (5), Register, December, 2000, No. 540, eff. 1-1-01; CR 02-002: am. Table Register April 2003 No. 568, eff. 5-1-03; CR 04-035: am. Table 84.10 Register November 2004, eff. 12-1-04; CR 08-055: am. Table 84.10 Register February 2009 No. 638, eff. 3-1-09; correction in (intro.), (1), (2) (a) 1., 2., (c), (d), (3) (a), (c) (intro.), (e) 3., (f) 1., (g), (5), (6), Table 384.10 made under s. 13.92 (4) (b) 7., Stats., Register December 2011 No. 672; CR 11-031: am. (3) (e) 3. Register June 2013 No. 690, eff. 7-1-13; EmR1423: emerg. renum. Table 84.10 rows 1 to 5 and 6 to 2 to 6 and 8 and am. 8, cr. Table rows 1 and 9, eff. 9-27-14; CR 14-056: renum. Table 84.10 rows 1 to 5 and 6 to 2 to 6 and 8 and am. 8, cr. Table rows 1 and 9 Register July 2015 No. 715, eff. 8-1-15; CR 17-065: am. (intro.), (2) (a) 2., renum. (2) (b) to (2) (b) 1., cr. (2) (b) 2., am. (2) (c), (d), (3) (title), (a), (c) (intro.), cr. (3) (c) 12., am. (3) (d), cr. (3) (d) 2. h., i., am. (3) (e) 1., renum. (3) (e) 2. a. to (3) (d) 2. and am., r. (3) (e) 2. b., am. (3) (f) 1., (g) Register June 2018 No. 750, eff. 7-1-18; CR 23-006: am. Table 384.10 line 3. Register September 2023 No. 813, eff. 10-1-23.
SPS 384.11 SPS 384.11Appurtenance, device, fixture, material, and method listings. Appurtenances, devices, fixtures, materials and methods shall conform to the referenced standard in Table 384.11. Appurtenances, devices, fixtures, materials, and methods shall be listed by a nationally recognized, ANSI accredited, third party agency acceptable to the department. Appurtenances, devices, fixtures, materials, and methods that do not conform to the listed standards may achieve code compliance via Alternate or Experimental approvals in accordance with s. SPS 384.50.
SPS 384.11 Note Note: See s. SPS 381.20 for complete standard designations and ch. SPS 384 Appendix for acceptable listing agencies. - See PDF for table PDF
a. The specific standard edition adopted is specified in s. SPS 381.20.
b. NSF Registration Guidelines for Proprietary Substances and Nonfood Compounds. The NSF Nonfood Compounds Registration Program is a continuation of the USDA product approval and listing program, which is based on meeting regulatory requirements including FDA 21 CFR for appropriate use, ingredient, and labeling: https://info.nsf.org/usda/psnclistings.asp.
c. Nominal size 2-in. CTS.
d. May not be used in temperature/pressure relief valve drain lines unless they are tested and rated for excessive conditions of 210°F (98.9°C) and 150.0 psig (1034 kPa), per ASME A112.4.1 or ASTM F877.
e. Steel and malleable iron fittings used in a water supply system shall be galvanized in accordance with ASTM A123/A123M j = https://info.nsf.org/usda/psnclistings.asp.
f. Threaded joints shall only be used on pipe of sch. 80 or heavier.
g. Closed loop boiler feed only, standard does not require NSF/ANSI 372 or NSF/ANSI/CAN-61 conformance.
h. Design shall conform to ASPE 45-2018.
i. Portland, Type II.
SPS 384.11 History History: Cr. Register, July, 2000, No. 535, eff. 9-1-00; CR 02-002: am. Table Register April 2003 No. 568, eff. 5-1-03; CR 04-035: am. Table 84.11 Register November 2004 No. 587, eff. 12-1-04; CR 08-055: am. Table 84.11 Register February 2009 No. 638, eff. 3-1-09; correction made under s. 13.92 (4) (b) 7., Stats., Register December 2011 No. 672; CR 23-006: r. and recr. Register September 2023 No. 813, eff. 10-1-23.
SPS 384.12 SPS 384.12Identification. Each length of pipe and each pipe fitting, trap, fixture, material, device, and product to be used in plumbing shall be marked as required by the applicable standard specified by reference in this chapter or as specified by rule in chs. SPS 381 to 387.
SPS 384.12 History History: Cr. Register, May, 1988, No. 389, eff. 6-1-88; am. Register, April, 2000, No. 532, eff. 7-1-00; renum. from s. Comm 84.11, Register, July, 2000, No. 535, eff. 9-1-00; CR 23-006: am. Register September 2023 No. 813, eff. 10-1-23.
SPS 384.13 SPS 384.13Penetrations of fire-resistive assemblies. Penetrations of fire-resistive assemblies, such as walls and floor-ceiling systems, by plumbing systems or plumbing materials shall be protected in accordance with requirements of chs. SPS 361 to 366.
Loading...
Loading...
Published under s. 35.93, Stats. Updated on the first day of each month. Entire code is always current. The Register date on each page is the date the chapter was last published.